Graco H25, H50, H40 important safety instructions Manual current control mode only

Page 32

e.Press to display actual tempera- tures.

Do not turn on hose heat without fluid in hoses.

f. Turn on heat zone by pressing

. Preheat hose (15-60 min). Indi-

cator will flash very slowly when fluid

reaches target temperature. Display shows actual fluid temperature in hose

near FTS.

Thermal expansion can cause overpressur- ization, resulting in equipment rupture and serious injury, including fluid injection. Do not pressurize system when preheating hose.

g. Turn on A and B heat zones by

pressing for each zone.

h.Hold to view electrical currents for each zone.

i.Hold to view heater control circuit board temperature.

Startup

j.Manual current control mode only:

When in manual current control mode, moni- tor hose temperature with thermometer. Install per instructions below. Thermometer reading must not exceed 160°F (71°C). Never leave machine unattended when in manual current control mode.

If FTS is disconnected or display shows diagnostic code E04, turn main power

switch OFF

then ON

to

clear diagnostic code and enter manual

current control mode. display will

show current to hose. Current is not lim- ited by target temperature.

Press or to adjust current setting.

To prevent overheating, install hose thermometer close to gun end, within operator view. Insert thermometer through foam cover of A component hose so stem is next to inner tube. Thermometer reading will be about 20°F less than actual fluid temperature.

If thermometer reading exceeds 160°F

(71°C), reduce current with key.

32

312062W

Image 32
Contents Important Safety Instructions OperationContents Systems GCP2R2 Models SeriesXP2 Series ApprovalsReactor Electrical Diagrams Supplied ManualsReactor Hydraulic Proportioner Part Description Part DescriptionRelated Manuals Electric Shock Hazard Skin Injection Hazard Pressurized Aluminum Parts Hazard Important Two-Component Material Information Isocyanate ConditionsMaterial Self-ignition Keep Components a and B SeparateFoam Resins with 245 fa Blowing Agents Changing MaterialsTypical Installation, with circulation Key for FIGSide Supply Detail Side Supply Detail MTypical Installation, without circulation Typical Installation, without circulationComponent Identification Detail of Reactor Fluid Manifold shroud removed for clarity Detail of Serial No Plate inside cabinetRed Stop Button Temperature Controls and IndicatorsMain Power Switch Actual Temperature Key/LED Target Temperature Key/LEDTemperature Scale Keys/LEDs Temperature Arrow KeysCircuit Breakers Size ComponentMotor Controls and Indicators Motor ON/OFF Key/LED PSI/BAR Keys/LEDsPark Key/LED Pressure Key/LEDSpray Adjustments Cycle Count Key/LEDHydraulic Pressure Control Knob Motor Control Arrow KeysGeneral equipment guidelines SetupLocate Reactor Phase Amps Watts Electrical Requirements KW/Full Load AmpsElectrical Requirements Full Load Voltage Peak System PartPower Cord Requirements Cord SpecificationConnect electrical cord Part Model AWG mmConnect feed pumps Install Fluid Temperature Sensor FTS Connect pressure relief linesConnect heated hose Close gun fluid manifold valves a and BConnect whip hose to gun fluid mani- fold Pressure check hoseCheck hydraulic fluid level Lubrication system setupGround system Startup Check generator fuel levelSet temperatures Manual current control mode only Change pressure imbalance setting optional Set pressureAvailable Pressure Imbalance Settings PSI BARSpraying Open gun fluid manifold valves a and B Standby Shutdown Pressure Relief Procedure Fluid Circulation LationCirculation Through Gun Manifold Diagnostic Codes Code Code Name Alarm ZoneMotor Control Diagnostic Codes Code Code Name Alarm orMaintenance Frequency of Oil Changes Ambient Recommended TemperatureFluid Inlet Strainer Screen Fluid Inlet StrainerPump Lubrication System Pump Lubrication SystemFlushing Top View DimensionsDimension In. mm Technical Data Category DataCoatings Performance Chart Performance ChartsFoam Performance Chart 110 Flow Rate in gpm lpmGraco Standard Warranty Graco Information