Graco H40, H50, H25 important safety instructions Technical Data, Category Data

Page 49

Technical Data

Technical Data

Category

Data

Maximum Fluid Working Pressure

Models H-25 and H-40: 2000 psi (13.8 MPa, 138 bar)

 

Model H-50 1 phase: 1700 psi (11.7 MPa, 11.7 bar)

 

Model H-50 3 phase: 2000 psi (13.8 MPa, 138 bar)

 

Models H-XP2 and H-XP3: 3500 psi (24.1 MPa, 241 bar)

Fluid:Oil Pressure Ratio

Models H-25 and H-40: 1.91:1

 

Model H-50: 1.64:1

 

Models H-XP2 and H-XP3: 2.79:1

Fluid Inlets

Component A (ISO): 1/2 npt(f), 250 psi (1.75 MPa, 17.5 bar) maximum

 

Component B (RES): 3/4 npt(f), 250 psi (1.75 MPa, 17.5 bar) maximum

Fluid Outlets

Component A (ISO): #8 (1/2 in.) JIC, with #5 (5/16 in.) JIC adapter

 

Component B (RES): #10 (5/8 in.) JIC, with #6 (3/8 in.) JIC adapter

Fluid Circulation Ports

1/4 npsm(m), with plastic tubing, 250 psi (1.75 MPa, 17.5 bar) maximum

Maximum Fluid Temperature

190°F (88°C)

Maximum Output (10 weight oil at

Model H-25: 22 lb/min (10 kg/min) (60 Hz)

ambient temperature)

Model H-XP2: 1.5 gpm (5.7 liter/min) (60 Hz)

 

Model H-50: 52 lb/min (24 kg/min) (60 Hz)

 

Model H-40: 45 lb/min (20 kg/min) (60 Hz)

 

Model H-XP3: 2.8 gpm (10.6 liter/min) (60 Hz)

Output per Cycle (A and B)

Models H-25 and H-40: 0.063 gal. (0.23 liter)

 

Model H-50: 0.073 gal. (0.28 liter)

 

Models H-XP2 and H-XP3: 0.042 gal. (0.16 liter)

Line Voltage Requirement

230V 1 phase and 230V 3 phase units: 195-264 Vac, 50/60 Hz

 

400V 3 phase units: 338-457 Vac, 50/60 Hz

Amperage Requirement

See Systems, page 3.

Heater Power

See Systems, page 3.

(A and B heaters total, no hose)

 

Hydraulic reservoir capacity

3.5 gal. (13.6 liters)

Recommended hydraulic fluid

Citgo A/W Hydraulic Oil, ISO Grade 46

Sound power, per ISO 9614-2

90.2 dB(A)

Sound pressure,

82.6 dB(A)

1 m from equipment

 

Weight

Units with 8.0 kW Heaters: 535 lb (243 kg)

 

Units with 12.0 kW Heaters: 597 lb (271 kg)

 

Units with 15.3 kW Heaters (H-25/H-XP2 models):562 lb (255 kg)

 

Units with 15.3 kW Heaters (H-40/H-XP3/H-50 models): 597 lb (271 kg)

 

Units with 20.4 kW Heaters: 597 lb (271 kg)

Wetted Parts

Aluminum, stainless steel, zinc-plated carbon steel, brass, carbide, chrome,

 

fluoroelastomer, PTFE, ultra-high molecular weight polyethylene, chemically

 

resistant o-rings

All other brand names or marks are used for identification purposes and are trademarks of their respective owners.

312062W

49

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Operation Important Safety InstructionsContents Systems GCP2R2 Series ModelsApprovals XP2 SeriesSupplied Manuals Reactor Electrical DiagramsReactor Hydraulic Proportioner Part Description Part DescriptionRelated Manuals Electric Shock Hazard Skin Injection Hazard Pressurized Aluminum Parts Hazard Isocyanate Conditions Important Two-Component Material InformationMaterial Self-ignition Keep Components a and B SeparateChanging Materials Foam Resins with 245 fa Blowing AgentsKey for FIG Typical Installation, with circulationSide Supply Detail Side Supply Detail MTypical Installation, without circulation Typical Installation, without circulationComponent Identification Detail of Serial No Plate inside cabinet Detail of Reactor Fluid Manifold shroud removed for clarityMain Power Switch Temperature Controls and IndicatorsRed Stop Button Target Temperature Key/LED Actual Temperature Key/LEDTemperature Scale Keys/LEDs Temperature Arrow KeysSize Component Circuit BreakersMotor ON/OFF Key/LED PSI/BAR Keys/LEDs Motor Controls and IndicatorsPark Key/LED Pressure Key/LEDCycle Count Key/LED Spray AdjustmentsHydraulic Pressure Control Knob Motor Control Arrow KeysLocate Reactor SetupGeneral equipment guidelines Electrical Requirements KW/Full Load Amps Phase Amps WattsElectrical Requirements Full Load Voltage Peak System PartCord Specification Power Cord RequirementsConnect electrical cord Part Model AWG mmConnect feed pumps Connect pressure relief lines Install Fluid Temperature Sensor FTSClose gun fluid manifold valves a and B Connect heated hoseConnect whip hose to gun fluid mani- fold Pressure check hoseGround system Lubrication system setupCheck hydraulic fluid level Check generator fuel level StartupSet temperatures Manual current control mode only Set pressure Change pressure imbalance setting optionalPSI BAR Available Pressure Imbalance SettingsSpraying Open gun fluid manifold valves a and B Standby Shutdown Pressure Relief Procedure Lation Fluid CirculationCirculation Through Gun Manifold Code Code Name Alarm Zone Diagnostic CodesCode Code Name Alarm or Motor Control Diagnostic CodesFrequency of Oil Changes Ambient Recommended Temperature MaintenanceFluid Inlet Strainer Fluid Inlet Strainer ScreenPump Lubrication System Pump Lubrication SystemFlushing Dimension In. mm DimensionsTop View Category Data Technical DataFoam Performance Chart Performance ChartsCoatings Performance Chart Flow Rate in gpm lpm 110Graco Information Graco Standard Warranty
Top Page Image Contents