Graco 258864 Charging the Battery, Charger Status Indicator Lights, Sprayer Status Indicator

Page 7

Charging the Battery

Charging the Battery

Batteries may leak, explode, cause burns or cause an explosion if mishandled.

Batteries are initially 50% charges to provide optimum battery life and require charging before first use. It takes approximately 45 minutes to charge a dead battery to 80%, at which point it can be used.It will take approxi- mately 75 minutes to fully charge a dead battery.

1.Slide battery into charger as shown (light will turn on within 5 seconds).

NOTE: Batteries can remain in the charger, which automatically switches to maintenance mode. It is not recommended to store the battery in the charger for longer than one week.

To reduce the risk of electric shock, only use Graco batteries with the Graco charger. Do not insert any foreign objects into the adapter cup.

NOTE: The amount sprayed with each battery varies depending on material, tip size, battery charge, and bat- tery temperature. 1 battery fully charged will spray approximately 1 gallon when using the 515 tip with latex paint. You will get less when using a smaller tip or thin- ner material.

NOTICE

Do not place a wet battery in the charger. Damage to equipment will occur.

Charger Status Indicator Lights

 

 

 

 

Label

Appearance

Description

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Solid green light

Indicates a full charge. Use the battery or leave it in the charger.

 

 

 

 

 

 

 

 

 

 

 

 

 

The automatic Maintenance Mode holds the batteries at full charge.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Flashing green light

Battery is charging, indicates 80% charge.

 

 

 

 

 

 

 

 

 

 

 

 

 

Battery can be used.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Flashing red light

Battery is charging, indicates less than 80% charge.

 

 

 

 

 

 

 

 

 

 

 

 

 

Do NOT use battery.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Solid red light

Battery is too hot or too cold to charge and must cool or warm up before

 

 

 

 

 

 

 

 

 

 

 

 

 

 

charging. Leave battery in charger.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sprayer Status Indicator

Light

Appearance

Description

 

No light

Normal operation.

 

Solid red

Battery is low on power and needs to be charged, or battery

 

 

is too cold and must warm up prior to spraying.

 

Flashing red

Battery temperature is too high, or tip is clogged.

 

 

See Troubleshooting, page 18.

NOTE: The indicator light is only visible when sprayer trigger is engaged. You must squeeze and hold the trigger to see the Sprayer Status Indicator.

3A0705E

7

Image 7
Contents 3A0705E Table of Contents Fire and Explosion Hazard Battery Hazard Component Identification Trigger Lock Pressure Relief ProcedurePrime/Relief Valve Position Charger Status Indicator Lights Charging the BatterySprayer Status Indicator Cleanup/Storage SetupInstalling Suction Tube InstallationSprayer Setup Starting a New Job or Refilling the Cup MaterialsReversible Tip Selection Chart Install Tip/Guard Assembly if not installedAiming Sprayer Triggering SprayerUnclogging Spray Tip/Guard Assembly Flushing Sprayer Shutdown and CleaningWater or flushing fluid. a soft brush can be used to Storage Cleaning Sprayer ExteriorTips Ref. Part Description Replacement Parts and KitsProblem Cause Solution TroubleshootingReplace tip. See Install Tip/Guard Assem Spray Pattern Diagnostics Problem Cause SolutionSpray pattern spits at Alternate Priming Method Removal Inlet Valve CleaningSprayer Technical DataGraco Information Graco Standard Warranty