Dukane 403-570-01 user manual Unpacking Welder, Packing List, Work Area, Qty Part Number

Page 21

Section 3 - Unpacking and Setup

Unpacking Welder

The Dual Servo Spin Welder is normally packed in a corrugated carton resting on a wooden shipping pallet. To unpack the welder follow these steps.

1.Remove the straps from the carton.

2.Open the top of the carton. Carefully remove any packing materials, cables and documentation.

3.Cut the tape at the bottom corners and unfold the flaps.

4.Remove the corrugated carton, but leave the welder on the pallet.

5.Leave the power cable wrapped up until after the welder has been placed in its working area and you are ready to begin hooking up power. This will pre- vent accidental kinking or pinching of the power cable.

Packing List

After removing the shipping container, check that you have the items listed in Table 3-I. Inspect the welder for damage. Report any damage immediately to the carrier and to Dukane Ultrasonics Service at (630) 762–4900. Also see Section 11 for information on contacting Dukane. Save all shipping and packing materials so they can be inspected in processing any claims that may arise.

Work Area

Allow sufficient area on either side of the Dual Servo Spin Welder for handling material, work pieces and fixtures. Provide ample room so that the movement of an operator or helper does not interfere with the work of another. Also be aware that under extreme conditions, small droplets of molten plastic may be spun off from the upper part.

Qty

Item

Part Number

 

 

 

 

 

SVT012VR or

1

Dual Servo Spin Welder

SVT032VR or

 

 

SVT042VR

 

 

 

1

Base Interface Cable

200-1124-3 or

200-1545-01

 

 

 

 

 

1

Dual Servo Spin Welder

403-570-XX

Manual

 

 

 

 

 

 

1

CD with Dual Servo Spin

___

Welder Utility

 

 

 

 

 

Table 3-IDual Servo Spin Welder Packing List

Dukane Manual Part No. 403-570-01

Page  15

Image 21
Contents Dual Servo Spin Welder Dukane Manual Part No Revision History RevisionSummary Date This page intentionally left blank Dukane Dual Servo Spin Welder ContentsThis page intentionally left blank Introduction SectionDukane Manual Part No Important User Information Read This Manual FirstDrawings and Tables SVT042VR Dual Servo Spin Welder OverviewKey Dual Servo Spin Welder Features This page intentionally left blank Safety Considerations This page intentionally left blank  Caution Health and Safety TipsRun Switches General SafetyPlastics Health Notice Electrical Safety Mechanical SafetyAC Power Receptacle This page intentionally left blank Unpacking and Setup This page intentionally left blank Packing List Unpacking WelderWork Area Qty Part NumberBench Capacity Securing to Work BenchLeveling Mounting HolesTooling Hub & Fixture Dimensions are in Inches mm20-Amp 240V Figure AC PowerControl Connectors Head Height AdjustmentBase Interface Connector User I/O ConnectorThis page intentionally left blank Display and Controls This page intentionally left blank 1Dual Servo Spin Welder Touch Screen Panel Touch Screen DisplayEmergency Stop Switch Operational SwitchesData I/O Connector Opti-Touch Run SwitchesBrigtly Lit Red LEDs This page intentionally left blank View Parts Touch Screen MenusThis page intentionally left blank Screen Layout RUN ModeView Parts Setup Menu PRE-WELD SetupTool Setup Trigger Position TOP of Stroke PositionPre-Spin Orientation Option Part Pickup OptionWeld Setup Weld Method SelectionTime Method Distance Method Rotation MethodOrientation Option Energy Method18Weld Torque Trigger Option Screen Torque Trigger OptionPOST-WELD Setup Hold SetupConstant Torque Option 22Hold Setup Screen for Distance Mode 25Process Limit Definitions Screen 1 Part Tests28RUN Screen with Part Test Failed Button Select Setup Tab Tools MenuUtilities Tab Third tab is labeled System Setup and is shown in Figure System Setup Tab34Vertical Lower Limit Setup Screen with Set Position Button 35Password-Protected Screens and Menus Setting Time and Date On Touch Screen Parameter Value Range Screen Parameter Name Min.Value Max.Value Resolution UnitsThis page intentionally left blank 55-56 Machine OperationThis page intentionally left blank AC Power Machine SetupAdjust Thruster Position on Column Base Interface CableTurn Power on Reset E-StopSet Tool Parameters Initialize Home WelderSet Weld Process Parameters Set Vertical Travel Lower Limit PositionStarting a Weld Cycle Stopping a Weld Cycle Setup SheetDual Servo Spin Welder Setup Sheet Optimizing Performance This page intentionally left blank Material Considerations Spin Welding ProcessSurface Speed Control ParametersSpeed Rev/minSpin Average Weld Diameter inchWeld Depth Press Axial SpeedPart Size HoldWeld Diameter Machine Peak RPM This page intentionally left blank Welder Data Export Software Installation, StartupThis page intentionally left blank Hardware Software Requirements Installation Startup, and Cable ConnectionsPart Data List Part DataFile Write Profile GraphsIncoming Data Plot DataSpin Torque Setpoint Servo and DebugWelding Process TroubleshootingThis page intentionally left blank Welding Process TroubleshootingMechanical WelderProblem Symptom Possible Cause Recommended Solution Faults Message Description Cause Possible Solution InstructionsMessage Description Cause Possible Solution Time or number of rotations Message Description Cause Possible Solution ErrorsMessage Description Cause Possible Solution This page intentionally left blank Maintenance This page intentionally left blank Maintenance AC Power CordThis page intentionally left blank Contacting Dukane This page intentionally left blank Identify Equipment Contacting DukaneUltrasonics Division WebsiteThis page intentionally left blank Specifications This page intentionally left blank Machine Weight Tooling SpecificationsPower Requirements Operating Environment2Dual Servo Spin Welder Dimensions Welder Model & Serial Number Identification NumbersThis page intentionally left blank Appendix a Connector PinoutsThis page intentionally left blank Figure A-1Base Interface Connector Base Interface ConnectorSignal Description Function User I/O ConnectorPin Signal Description Function Slide Kit ConnectorAutomation Wiring Data Port ConnectorFigure A-5Schematic of Operate and Abort This page intentionally left blank Tooling Appendix BThis page intentionally left blank Explanation of Inertia Moment of InertiaTool and Fixture Design Appendix C Optional FeaturesThis page intentionally left blank Figure C-1Upper Tool Vacuum System Upper Tool VacuumFigure C-2 Remote Touch Screen Components Remote Touch ScreenDukane ISO