Dukane 403-570-01 Important User Information, Read This Manual First, Drawings and Tables

Page 9

Section 1 - Introduction

Important User Information

Read This Manual First

Before operating the Dual Servo Spin Welder, read this User’s Manual to become familiar with the system. This will ensure correct and safe operation. The manual is organized to allow you to learn how to safely operate this system. The examples given are chosen for their simplicity to illustrate basic setup procedures.

Notes and Tips

Throughout this manual we use NOTES to provide information that is important for the successful application and understanding of the system. A NOTE block is shown to the right.

Cautions and Warnings

In addition, we use special notices to make you aware of safety considerations. These are the CAUTION and WARNING blocks as shown here. They represent increasing levels of important information. These statements help you to identify and avoid hazards and recognize the consequences. Different symbols also accompany the CAUTION and WARNING blocks to indicate whether the notice pertains to a general condition or practice, an electrical safety issue, a hand protection issue or other condition.

Drawings and Tables

The figures and tables are identified by the section number followed by a sequence number. The sequence number begins with one in each section. The figures and tables are numbered separately. The figures use arabic sequence numbers (e.g. –1, –2, –3) while the tables use roman sequence numerals (e.g. –I, –II, –III). As an example, Figure 3–2 would be the second illustration in section three while Table 3—II would be the second table in section three.

NOTE

NOTE statements provide additional in- formation or highlight procedures..

CAUTION

CAUTION statements iden- tify conditions or practices that could result in damage to the equipment or other property..

WARNING

WARNING statements point out conditions or practices that could result in person- al injury or loss of life.

Condition

Electrical

Crush

or Practice

Hazard

Hazard

Dukane Manual Part No. 403-570-01

Page

Image 9
Contents Dual Servo Spin Welder Dukane Manual Part No Revision History RevisionSummary Date This page intentionally left blank Dukane Dual Servo Spin Welder ContentsThis page intentionally left blank Introduction SectionDukane Manual Part No Important User Information Read This Manual FirstDrawings and Tables SVT042VR Dual Servo Spin Welder OverviewKey Dual Servo Spin Welder Features This page intentionally left blank Safety Considerations This page intentionally left blank  Caution Health and Safety TipsRun Switches General SafetyPlastics Health Notice Electrical Safety Mechanical SafetyAC Power Receptacle This page intentionally left blank Unpacking and Setup This page intentionally left blank Packing List Unpacking WelderWork Area Qty Part NumberBench Capacity Securing to Work BenchLeveling Mounting HolesTooling Hub & Fixture Dimensions are in Inches mm20-Amp 240V Figure AC PowerControl Connectors Head Height AdjustmentBase Interface Connector User I/O ConnectorThis page intentionally left blank Display and Controls This page intentionally left blank 1Dual Servo Spin Welder Touch Screen Panel Touch Screen DisplayEmergency Stop Switch Operational SwitchesData I/O Connector Opti-Touch Run SwitchesBrigtly Lit Red LEDs This page intentionally left blank View Parts Touch Screen MenusThis page intentionally left blank Screen Layout RUN ModeView Parts Setup Menu PRE-WELD SetupTool Setup Trigger Position TOP of Stroke PositionPre-Spin Orientation Option Part Pickup OptionWeld Setup Weld Method SelectionTime Method Distance Method Rotation MethodOrientation Option Energy Method18Weld Torque Trigger Option Screen Torque Trigger OptionPOST-WELD Setup Hold SetupConstant Torque Option 22Hold Setup Screen for Distance Mode 25Process Limit Definitions Screen 1 Part Tests28RUN Screen with Part Test Failed Button Select Setup Tab Tools MenuUtilities Tab Third tab is labeled System Setup and is shown in Figure System Setup Tab34Vertical Lower Limit Setup Screen with Set Position Button 35Password-Protected Screens and Menus Setting Time and Date On Touch Screen Parameter Value Range Screen Parameter Name Min.Value Max.Value Resolution UnitsThis page intentionally left blank 55-56 Machine OperationThis page intentionally left blank AC Power Machine SetupAdjust Thruster Position on Column Base Interface CableTurn Power on Reset E-StopSet Tool Parameters Initialize Home WelderSet Weld Process Parameters Set Vertical Travel Lower Limit PositionStarting a Weld Cycle Stopping a Weld Cycle Setup SheetDual Servo Spin Welder Setup Sheet Optimizing Performance This page intentionally left blank Material Considerations Spin Welding ProcessSurface Speed Control ParametersSpeed Rev/minSpin Average Weld Diameter inchWeld Depth Press Axial SpeedPart Size HoldWeld Diameter Machine Peak RPM This page intentionally left blank Welder Data Export Software Installation, StartupThis page intentionally left blank Hardware Software Requirements Installation Startup, and Cable ConnectionsPart Data List Part DataFile Write Profile GraphsIncoming Data Plot DataSpin Torque Setpoint Servo and DebugWelding Process TroubleshootingThis page intentionally left blank Welding Process TroubleshootingMechanical WelderProblem Symptom Possible Cause Recommended Solution Faults Message Description Cause Possible Solution InstructionsMessage Description Cause Possible Solution Time or number of rotations Message Description Cause Possible Solution ErrorsMessage Description Cause Possible Solution This page intentionally left blank Maintenance This page intentionally left blank Maintenance AC Power CordThis page intentionally left blank Contacting Dukane This page intentionally left blank Identify Equipment Contacting DukaneUltrasonics Division WebsiteThis page intentionally left blank Specifications This page intentionally left blank Machine Weight Tooling SpecificationsPower Requirements Operating Environment2Dual Servo Spin Welder Dimensions Welder Model & Serial Number Identification NumbersThis page intentionally left blank Appendix a Connector PinoutsThis page intentionally left blank Figure A-1Base Interface Connector Base Interface ConnectorSignal Description Function User I/O ConnectorPin Signal Description Function Slide Kit ConnectorAutomation Wiring Data Port ConnectorFigure A-5Schematic of Operate and Abort This page intentionally left blank Tooling Appendix BThis page intentionally left blank Explanation of Inertia Moment of InertiaTool and Fixture Design Appendix C Optional FeaturesThis page intentionally left blank Figure C-1Upper Tool Vacuum System Upper Tool VacuumFigure C-2 Remote Touch Screen Components Remote Touch ScreenDukane ISO