Dukane 403-570-01 user manual Tooling Hub & Fixture, Dimensions are in Inches mm

Page 23

Section 3 - Unpacking and Setup

Tooling Hub & Fixture

The upper tooling attaches to a hub using four 5/16”- 18 screws, spring lock washers, and flat washers.

Figure 3–2 (a & b) gives the dimensions of the tooling hubs. The hubs have precision slots to accommodate an indexing pin on the tool so that the tool can be mounted in a consistent orientation relative to the hub.

The lower tooling fixture attaches to the base platen using M10–1.5 cap screws. See Figure 3–3 for the detailed measurements of the mounting holes in the base platen.

3.00 [76.2] B.C.

15X .316 [8.03]

22.5° TYP.

.250 +- ..002000[6.35 +- ..0500]

3.60 [91.4]

.30 [7.6]

.21 [5.3]

1.000 +- ..000001[25.40 +- ..0003]

16.50

 

0.50

 

(419)

8.25

DIA. HOLES

13.25

(209.6)

(12.7)

 

 

 

(336.6)

 

0.50 RADIUS

 

 

(12.7)

 

Dimensions are in INCHES [mm]

Figure 3–2aUpper Tooling Hub Dimensions

for Models SVT032VR and SVT042VR

5.00 [127.0] B.C.

4 x .404 [10.26]

(EQUALLY SPACED)

6.05

(153.7)

7.61

(193.3)

12.38

(314.5)

24.84

(631)

M12 X 1.75

6H TAP THRU

5 PLACES

 

 

M10 X 1.5 2B TAP THRU EQUALLY

 

 

SPACED AND LOCATED AT TRUE

 

 

POSITION WITHIN 0.015 DIA ON

 

 

(2) TWO BOLT CIRCLES 8 PLACES

 

 

7.00 inch BOLT CIRCLE

 

 

125.0 mm BOLT CIRCLE

 

 

12.00 inch BOLT CIRCLE

 

 

1.52/(38.6)

 

 

 

 

1.50/(38.1)

 

 

2.00/(50.8)

3.02/(76.7)

 

 

 

2.25

TYP.

 

 

(57.2)

2.63

TYP.

 

 

(66.8)

 

inches

 

 

 

(millimeters)

45°

 

 

 

.376 +- ..000003[9.55 +- ..0008]

 

 

5.90 [149.9]

.50 [12.7]

 

.35 [8.9]

1.000 +- .001.000[25.40 +- .03.00]

Dimensions are in INCHES [mm]

Figure 3–3Lower Base Fixture Mounting

Figure 3–2bUpper Tooling Hub Dimensions for SVT012VR

Dukane Manual Part No. 403-570-01

Page  17

Image 23
Contents Dual Servo Spin Welder Dukane Manual Part No Summary Date Revision HistoryRevision This page intentionally left blank Dukane Dual Servo Spin Welder ContentsThis page intentionally left blank Introduction SectionDukane Manual Part No Drawings and Tables Important User InformationRead This Manual First SVT042VR Dual Servo Spin Welder OverviewKey Dual Servo Spin Welder Features This page intentionally left blank Safety Considerations This page intentionally left blank  Caution Health and Safety TipsPlastics Health Notice Run SwitchesGeneral Safety AC Power Receptacle Electrical SafetyMechanical Safety This page intentionally left blank Unpacking and Setup This page intentionally left blank Qty Part Number Unpacking WelderPacking List Work AreaMounting Holes Securing to Work BenchBench Capacity LevelingTooling Hub & Fixture Dimensions are in Inches mm20-Amp 240V Figure AC PowerUser I/O Connector Head Height AdjustmentControl Connectors Base Interface ConnectorThis page intentionally left blank Display and Controls This page intentionally left blank 1Dual Servo Spin Welder Touch Screen Panel Touch Screen DisplayEmergency Stop Switch Operational SwitchesBrigtly Lit Red LEDs Data I/O ConnectorOpti-Touch Run Switches This page intentionally left blank View Parts Touch Screen MenusThis page intentionally left blank Screen Layout RUN ModeView Parts Tool Setup Setup MenuPRE-WELD Setup Trigger Position TOP of Stroke PositionPre-Spin Orientation Option Part Pickup OptionTime Method Weld SetupWeld Method Selection Distance Method Rotation MethodOrientation Option Energy Method18Weld Torque Trigger Option Screen Torque Trigger OptionConstant Torque Option POST-WELD SetupHold Setup 22Hold Setup Screen for Distance Mode 25Process Limit Definitions Screen 1 Part Tests28RUN Screen with Part Test Failed Button Utilities Tab Select Setup TabTools Menu Third tab is labeled System Setup and is shown in Figure System Setup Tab34Vertical Lower Limit Setup Screen with Set Position Button 35Password-Protected Screens and Menus Setting Time and Date On Touch Screen Parameter Value Range Screen Parameter Name Min.Value Max.Value Resolution UnitsThis page intentionally left blank 55-56 Machine OperationThis page intentionally left blank Base Interface Cable Machine SetupAC Power Adjust Thruster Position on ColumnInitialize Home Welder Reset E-StopTurn Power on Set Tool ParametersSet Weld Process Parameters Set Vertical Travel Lower Limit PositionStarting a Weld Cycle Stopping a Weld Cycle Setup SheetDual Servo Spin Welder Setup Sheet Optimizing Performance This page intentionally left blank Material Considerations Spin Welding ProcessSurface Speed Control ParametersAverage Weld Diameter inch Rev/minSpeed SpinWeld Depth Press Axial SpeedWeld Diameter Machine Peak RPM Part SizeHold This page intentionally left blank Welder Data Export Software Installation, StartupThis page intentionally left blank Hardware Software Requirements Installation Startup, and Cable ConnectionsPart Data List Part DataPlot Data Profile GraphsFile Write Incoming DataSpin Torque Setpoint Servo and DebugWelding Process TroubleshootingThis page intentionally left blank Welding Process TroubleshootingMechanical WelderProblem Symptom Possible Cause Recommended Solution Faults Message Description Cause Possible Solution InstructionsMessage Description Cause Possible Solution Time or number of rotations Message Description Cause Possible Solution ErrorsMessage Description Cause Possible Solution This page intentionally left blank Maintenance This page intentionally left blank Maintenance AC Power CordThis page intentionally left blank Contacting Dukane This page intentionally left blank Website Contacting DukaneIdentify Equipment Ultrasonics DivisionThis page intentionally left blank Specifications This page intentionally left blank Operating Environment Tooling SpecificationsMachine Weight Power Requirements2Dual Servo Spin Welder Dimensions Welder Model & Serial Number Identification NumbersThis page intentionally left blank Appendix a Connector PinoutsThis page intentionally left blank Figure A-1Base Interface Connector Base Interface ConnectorSignal Description Function User I/O ConnectorPin Signal Description Function Slide Kit ConnectorAutomation Wiring Data Port ConnectorFigure A-5Schematic of Operate and Abort This page intentionally left blank Tooling Appendix BThis page intentionally left blank Explanation of Inertia Moment of InertiaTool and Fixture Design Appendix C Optional FeaturesThis page intentionally left blank Figure C-1Upper Tool Vacuum System Upper Tool VacuumFigure C-2 Remote Touch Screen Components Remote Touch ScreenDukane ISO