Carrier 50PEC09-18 Configuration Service, Point Name Password Editable Range Default Level

APPENDIX A — WSHP SCREEN OPEN CONFIGURATION (cont)

SCREEN NAME

Configuration

→

Service

Configuration

POINT NAME	PASSWORD	EDITABLE	RANGE	DEFAULT	NOTES
	LEVEL
# of Fan Speeds		X	1,2,3	3	Used to set number of
					fan motor speeds
					When set to Fan On, G output is
					energized when ever any fan speed
G Output Type		X	Fan On/Fan Low	Fan On	is active (required for ECM and Fan
					control board). When set to Fan
					Low, output is only energized for
					Low Speed
Compressor Stages		X	One Stage/Two Stages	One Stage	Defines the number of
					stages of compression
Reversing Valve Type		X	O type output/B type output	O type	Determines reversing valve
					signal output type
Leaving Air Auxiliary		X	None/2-Position HW/1 Stage	None	Determines Auxiliary
Heat Type			Electric/Modulating HW		Reheat Coil Type
Entering Air Water		X	None/2-Position/Modulating	None	Determines Entering Air
Economizer Type					Economizer Coil Type
2-Position Water		X	Normally Closed/Normally Open	Normally	Determines type of 2-position
Valve Type				Closed	water valve used
Modulating Water		X	Normally Closed/Normally Open	Normally	Determines type of modulating
Valve Type				Closed	water valve used
Ventilation Damper		X	None/2-Position/DCV	None	Determines Type of ventilation
Type					damper control to be used
					Used to determine ventilation
Damper Actuator Type		X	(0-10 volt)/(2-10 volt)	0-10 volt	damper output signal range
					(closed - open)
Humidity Sensor		X	None/Installed	None	Set to Installed if Humidity
					sensor is present
Factory Dehumidifica-	Admin Password				Set to Installed if factory-installed
	level access only	X	None/Installed	None	dehumidification reheat coil
tion Reheat Coil					is present
Occupancy		X	Occupied Open/Occupied Closed	Occupied	Used to determine external occu-
Input Logic				CLOSED	pancy switch contact occupied state
Condensate Switch		X	5 - 600 seconds	10 sec	Delay before equipment alarms on
Alarm Delay					high condensate level
Condensate Switch		X	Alarm OPEN/Alarm CLOSED	Alarm	Determine Alarm state of
Alarm State				CLOSED	condensate switch input
Minimum Condenser			25 - 60 ° F	60 ° F	Determines the minimum
Water Temperature in		X			acceptable water loop temperature
Heating					to start heating
Maximum Condenser			65 - 100 ° F	90 ° F	Determines the maximum
Water Temperature in		X			acceptable water loop temperature
Heating					to start heating
Minimum Condenser			30 - 60 ° F	60 ° F	Determines the minimum
Water Temperature in		X			acceptable water loop temperature
Cooling					to start cooling
Maximum Condenser			85 - 120 ° F	95 ° F	Determines the maximum
Water Temperature in		X			acceptable water loop temperature
Cooling					to start cooling
IAQ sensor		X	0 - 5 ma	4 ma	Minimum output current (mA)
minimum input					for IAQ sensor
IAQ sensor		X	5 - 20 ma	20 ma	Maximum output current (mA) for
maximum input					IAQ sensor
IAQ sensor		X	0 - 9999 ppm	0 ppm	Corresponding value in ppm for
minimum output					minimum output current
IAQ sensor		X	0 - 9999 ppm	2000 ppm	Corresponding value in ppm for
maximum output					maximum output current

	LEGEND
BAS	— Building Automation System
DCV	— Demand Controlled Ventilation
IAQ	— Indoor Air Quality
OAT	— Outdoor Air Temperature
RH	— Relative Humidity
SAT	— Supply Air Temperature
SPT	— Space Temperature
TPI	— Third Party Integration

54