Porter-Cable PC1800DS Operating Instructions, Switch, Operation Figure E, Detail Sanding

Page 10

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 10

TO REMOVE BATTERY PACK: Depress the battery release button as shown in figure D and pull battery pack out of tool.

Operating Instructions

D

: To reduce the risk of serious personal injury, read and follow all important

safety warnings and instructions prior to using this tool.

Switch

To turn the tool ON, hold it as shown in figure E and push the portion of the switch marked "I". To turn the tool OFF, push the portion of the switch marked "O".

Operation (Figure E)

Grasp product as shown in figure E and turn it on. NOTE: Do not rest fingers on platen during use. Move it in long sweeping strokes across the surface, letting it do the work. Light pressure is all that is required for sanding. Excessive pressure will slow the tool and produce inferior results. Check your work often, product is capable of removing material rapidly.

E

: Shock hazard. Under no circumstances should this product be used near water.

: To reduce the risk of injury, turn off and remove battery from the tool before making any adjustments or removing or installing attachments or accessories.

Detail Sanding

Your tool is equipped with a teardrop base which allows you to use it on large flat surfaces and tight spots or corners.

The pad tips may wear unevenly, depending on use. The pads are designed to allow you to interchange and /or rotate the diamond tip.

Fitting sanding sheets (figure F)

•Detach the two diamond-shaped tips from the sanding sheet.

•Hold the tool with the sanding base facing upwards.

•Place the sanding sheet onto the sanding base. The diamond-shaped tip can be reversed and replaced when worn.

•When the front part of the tip is worn, detach it from the sheet, reverse it and press it onto the sanding base again.

•When the whole tip is worn, remove it from the sanding base and fit a new tip.

F

10

Image 10

Contents Advertencia Léase Este Catalog NumberGeneral Power Tool Safety Warnings Specific Safety Rules Safety Guidelines Definitions Important Safety Instructions for Battery Chargers SymbolsFunctional Description Important Safety Instruction for Battery Packs Read ALL InstructionsCharging Procedure Battery CAP InformationStorage Recommendations HOT/COLD Pack Delay Charger DiagnosticsBAD Battery Problem Power LineCleaning and disposal Personal safetyEnvironmental safety Lead based paintOperation Figure E SwitchOperating Instructions Detail SandingDust Collection / Vacuum Port Adaptor figure Tip of the Sanding Base figure GFinger Attachment figure H Hints for optimum useReplacement Parts Service and Repairs TroubleshootingMaintenance Rbrc SealThree Year Limited Warranty AccessoriesDE Catalogue 90550099 PC1800DS Crdl Sander Revised 4/1/09 152 PM 90550099 PC1800DS Crdl Sander Revised 4/1/09 152 PM Consignes DE Sécurité Particulières Lignes Directrices EN Matière DE Sécurité DéfinitionsSymboles Conserver CES DirectivesDescription Fonctionnelle Lire Toutes LES Directives Information Concernant LE Capuchon DU BLOC-PILE Recommandations EN Matière DE RangementFonctions DE Diagnostic DU Chargeur Procédure DE ChargeBLOC-PILES Laissé Dans LE Chargeur Fonction DE Suspension DU BLOC-PILES CHAUD/FROIDProblème Avec LE Secteur Remarques Importantes Pour LE ChargementProtection de l’environnement Ponçage Peintue à base de plombSécurité personnelle Nettoyage et déchetsFonctionnement Fig. E FonctionnementInterrupteur Fixation du papier abrasif Fig. FAdaptateur d’orifice de dépoussiérage/d’aspiration Fig Accessoire doigt de ponçage Fig. HPointe de la base abrasive Fig. G Conseils pour optimiser l’utilisationLE Sceau Srprcmc DépannagePièces DE Rechange Entretien ET Réparation AccessoiresEntretien Garantie Limitée DE Trois ANSRemplacement DES Étiquettes D’AVERTISSEMENT Catálogo N 90550099 PC1800DS Crdl Sander Revised 4/1/09 152 PM 90550099 PC1800DS Crdl Sander Revised 4/1/09 152 PM Normas Específicas DE Seguridad Pautas DE SEGURIDAD/DEFINICIONESConserve Estas Instrucciones SímbolosDescripción DE LAS Funciones LEA Todas LAS Instrucciones Procedimiento DE Carga Información Acerca DEL Protector DE LA BateríaRecomendaciones CON Respecto AL Almacenamiento Diagnóstico DEL CargadorDejar LA Batería EN EL Cargador Línea DE Potencia CON ProblemasRetraso POR Paquete CALIENTE/FRÍO Notas Importantes Sobre LA CargaSeguridad ambiental Lijado Lijado de pinturas con base de plomoSeguridad personal Limpieza y desechoInterruptor Instrucciones DE OperaciónOperacion Fig. E Punta de la base para lijar fig. G Lijado de detalleMontaje del papel de lija Fig. F Dispositivo para detalles finos Fig. HAdaptador para el colector de la aspiradora figura Consejos para un uso óptimoMantenimiento Detección DE ProblemasPiezas DE Repuesto Garantía Limitada DE Tres Años Mantenimiento Y ReparacionesAccesorios Reemplazo DE LAS Etiquetas DE AdvertenciaEspecificaciones