Juniper Networks C4000 manual Removing and Installing a Hard Drive, C2000 Power Supply

Page 48

C2000 and C4000 1.0.x Hardware Guide

2.Slide the locking tab (ejector button) to the left to release the module. See Figure 11 and Figure 12.

3.Hold the tab to the left, and using the handle, slowly pull the power supply module out.

To install a power supply module:

1.Hold the locking tab (ejector button) to the left, and slowly slide the module into the chassis until it clicks into place.

2.Insert the power cord into the AC power IEC receptacle.

Figure 11: C2000 Power Supply

Figure 12: C4000 Power Supply

Removing and Installing a Hard Drive

NOTE: If your system is powered on, see the SRC–PE Getting Started User Guide for commands to run before performing these steps.

To remove a hard drive:

1.Slide the locking tab in the bottom-right corner to the right to release the hard drive.

2.Hold the tab to the right and slowly pull the unit out.

To install a hard drive, hold the locking tab to the right and slowly slide the unit into the chassis until it clicks into place.

34■ Removing and Installing a Hard Drive

Image 48

Contents C2000 and C4000 Hardware Guide Series Platforms Hardware Guide Iii End User License AgreementPage Table of Contents Part Hardware Maintenance Procedures and Specifications Chapter Setting the Initial ConfigurationChapter Managing RAID Disks on a C-series Platform Part Index About This Guide ObjectivesAudience Documentation Conventions Text ConventionsRelated Juniper Networks Documentation User@host# set local-addressJuniper Networks C-series and SRC Technical Publications Core Documentation SetObtaining Documentation Documentation FeedbackRequesting Support Product Overview C2000 and C4000 1.0.x Hardware Guide Product Overview Series Platform Overview System DescriptionSeries Platform Models Series Model Differences C2000, Front ViewSeries Model Components C4000, Rear ViewNetwork Management Tools CLI ManagementSnmp MIB Management Page Initial Installation C2000 and C4000 1.0.x Hardware Guide Initial Installation Unpacking and Inspecting the C-series Platform Before You BeginInspecting System Components and Accessories Unpacking the UnitsIf You Detect or Suspect Damage Contacting Juniper NetworksInstalling and Cabling the C-series Platform Freestanding InstallationRack-Mounted Installation Installation GuidelinesInstalling the System Preparing the Equipment RacksCabling the System Cabling the Management ConsoleCabling the System for Power Cabling Ethernet InterfacesC2000, Front View Next Step Powering Up the C-series Platform Powering UpStatus LEDs Model LEDsSetting the Initial Configuration Configuration OverviewSetting Up Management Access and Logging Configuring the Juniper Networks Database Configuring Hostname and Domain Parameters Edit Root@host# set system host-name my-hostnameConfiguring the System for Remote Access Configuring the System to Accept SSH and Telnet Connections Adding an Admin User Account Set the password of the user C2000 and C4000 1.0.x Hardware Guide Next Step Hardware Maintenance Procedures and Specifications Page Maintaining the System Required Tools and ItemsCleaning the System Removing and Installing a FanStoring Modules and Components Removing and Installing a Power Supply Module Removing and Installing a Hard Drive System Specifications C2000 Model SpecificationsC2000 Model Specifications C4000 Model Specifications C4000 Model SpecificationsSystem Specifications Page Managing RAID Disks on a C-series Platform Series Platform Data StorageManaging Disks in a C-series Platform Replacing a DiskReinitializing an Active Disk Viewing Information About Disks on a C-series PlatformShow disk status Output Fields Field Name Field DescriptionInstallation Guidelines and Requirements Your Preinstallation ResponsibilitiesEnvironmental Requirements Regulatory CompliancesSafety Guidelines Equipment Rack Requirements Mechanical RequirementsProper Rack Installation Space RequirementsCabling Recommendations Product Reclamation and Recycling Program Hardware Compliance Federal Communications Commission FCC StatementFCC Requirements for Consumer Products Industry Canada Notice CS-03 Avis CS-03 dIndustrie CanadaC. Explanatory Notes Equipment Attachment Limitations EC Declaration of Conformity Return Procedure Contacting Customer Support and Returning HardwareContacting Customer Support Locating Component Serial Numbers Information You Might Need to Supply to JtacReturning Products for Repair or Replacement Tools and Parts RequiredPacking Instructions for Returning a Chassis Remove the chassis from the rack Declaration of Conformity Declaration of ConformityPage Index C2000 and C4000 1.0.x Hardware Guide Index Compliance Manuals