Juniper Networks C4000, C2000 manual Cabling Ethernet Interfaces, Cabling the System for Power

Page 30

C2000 and C4000 1.0.x Hardware Guide

■Two 10/100Base-T Ethernet ports—Each accepts an RJ-45 (male) connector, providing an out-of-band connection for LAN access through a Telnet session, SSH, or SNMP.

■One RS-232 management port—Accepts a DB-9 (female) connector. This port provides direct CLI access from a console terminal.

The management port is considered a data terminal equipment (DTE) interface. Direct connection to a terminal or PC (which also has DTE interfaces) requires a crossover cable.

See “Setting the Initial Configuration” on page 21 for more information about management access.

Connecting to the Network

To connect the system to the network:

1.Insert an Ethernet cable (RJ-45) connector into the 10/100Base-T (RJ-45) port on the system until it clicks into place.

2.Connect the other end of the cable to the appropriate Ethernet network for an out-of-band connection.

Connecting to a Console Terminal

When you connect a console directly to the system, use a cable appropriate for your terminal connector. The cable must have a female DB-9 connector to attach to the RS-232 port on the system.

To connect the console:

1.Insert the female DB-9 connector into the RS-232 port, and tighten the screws.

2.Connect the other end of the cable to your terminal's serial port (VT100/ANSI).

Cabling Ethernet Interfaces

Port ETH0 and ETH1 on the C2000 model and the C4000 model accept RJ-45 10/100/1000Base-T Ethernet (copper) interfaces. Port ETH2 and port ETH3 on the C2000 model and the C4000 model accept SFPs.

Cabling the System for Power

After you have correctly cabled the system, you can then attach the power cord. See Figure 8 and Figure 10. See “System Specifications” on page 35 for the power requirements for the system.

To cable the system for power:

1.Insert the power cord into the AC power IEC receptacle.

16■ Cabling the System

Image 30

Contents C2000 and C4000 Hardware Guide Series Platforms Hardware Guide Iii End User License AgreementPage Table of Contents Part Hardware Maintenance Procedures and Specifications Chapter Setting the Initial ConfigurationChapter Managing RAID Disks on a C-series Platform Part Index About This Guide ObjectivesAudience Documentation Conventions Text ConventionsRelated Juniper Networks Documentation User@host# set local-addressJuniper Networks C-series and SRC Technical Publications Core Documentation SetObtaining Documentation Documentation FeedbackRequesting Support Product Overview C2000 and C4000 1.0.x Hardware Guide Product Overview Series Platform Overview System DescriptionSeries Platform Models Series Model Differences C2000, Front ViewSeries Model Components C4000, Rear ViewNetwork Management Tools CLI ManagementSnmp MIB Management Page Initial Installation C2000 and C4000 1.0.x Hardware Guide Initial Installation Unpacking and Inspecting the C-series Platform Before You BeginIf You Detect or Suspect Damage Inspecting System Components and AccessoriesUnpacking the Units Contacting Juniper NetworksInstalling and Cabling the C-series Platform Freestanding InstallationInstalling the System Rack-Mounted InstallationInstallation Guidelines Preparing the Equipment RacksCabling the System Cabling the Management ConsoleCabling the System for Power Cabling Ethernet InterfacesC2000, Front View Next Step Powering Up the C-series Platform Powering UpStatus LEDs Model LEDsSetting the Initial Configuration Configuration OverviewSetting Up Management Access and Logging Configuring the Juniper Networks Database Configuring Hostname and Domain Parameters Edit Root@host# set system host-name my-hostnameConfiguring the System for Remote Access Configuring the System to Accept SSH and Telnet Connections Adding an Admin User Account Set the password of the user C2000 and C4000 1.0.x Hardware Guide Next Step Hardware Maintenance Procedures and Specifications Page Maintaining the System Required Tools and ItemsCleaning the System Removing and Installing a FanStoring Modules and Components Removing and Installing a Power Supply Module Removing and Installing a Hard Drive System Specifications C2000 Model SpecificationsC2000 Model Specifications C4000 Model Specifications C4000 Model SpecificationsSystem Specifications Page Managing RAID Disks on a C-series Platform Series Platform Data StorageManaging Disks in a C-series Platform Replacing a DiskReinitializing an Active Disk Viewing Information About Disks on a C-series PlatformShow disk status Output Fields Field Name Field DescriptionInstallation Guidelines and Requirements Your Preinstallation ResponsibilitiesEnvironmental Requirements Regulatory CompliancesSafety Guidelines Equipment Rack Requirements Mechanical RequirementsProper Rack Installation Space RequirementsCabling Recommendations Product Reclamation and Recycling Program Hardware Compliance Federal Communications Commission FCC StatementFCC Requirements for Consumer Products Industry Canada Notice CS-03 Avis CS-03 dIndustrie CanadaC. Explanatory Notes Equipment Attachment Limitations EC Declaration of Conformity Return Procedure Contacting Customer Support and Returning HardwareContacting Customer Support Locating Component Serial Numbers Information You Might Need to Supply to JtacReturning Products for Repair or Replacement Tools and Parts RequiredPacking Instructions for Returning a Chassis Remove the chassis from the rack Declaration of Conformity Declaration of ConformityPage Index C2000 and C4000 1.0.x Hardware Guide Index Compliance Manuals