Juniper Networks C2000 manual Hardware Compliance, Federal Communications Commission FCC Statement

Page 63

Chapter 9: Installation Guidelines and Requirements

Hardware Compliance

C–series platforms meet the hardware compliance requirements in this topic.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This equipment is designed for use with properly shielded and terminated cables. Refer to the installation sections of this manual before operation.

Reference: CFR 47, Part 15J, Sect 15.105 April 18, 1989

Caution: Changes or Modifications to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Requirements for Consumer Products

This equipment complies with FCC rules, Part 68. On the back side of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. If requested, provide this information to your telephone company.

If this equipment causes harm to the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify you in advance. But if advance notice isn't practical, you will be notified as soon as possible. You will be advised of your right to file a complaint with the FCC.

Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of your equipment. If they do, you will be given advance notice so as to give you an opportunity to maintain uninterrupted service.

If you experience trouble with this equipment, please contact the manufacturer for warranty/repair information. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning.

Food and Drug Administration, Center for Devices and Radiological Health

This equipment complies with 21 CFR 1040.10 and 1040.11 for the safe use of lasers.

Hardware Compliance ■ 49

Page 62 Page 64
Image 63
Page 62 Page 64
Contents C2000 and C4000 Hardware Guide Series Platforms Hardware Guide End User License Agreement IiiPage Table of Contents Chapter Setting the Initial Configuration Part Hardware Maintenance Procedures and SpecificationsChapter Managing RAID Disks on a C-series Platform Part Index About This Guide ObjectivesAudience Text Conventions Documentation ConventionsUser@host# set local-address Related Juniper Networks DocumentationCore Documentation Set Juniper Networks C-series and SRC Technical PublicationsDocumentation Feedback Obtaining DocumentationRequesting Support Product Overview C2000 and C4000 1.0.x Hardware Guide Product Overview Series Platform Overview System DescriptionSeries Platform Models C2000, Front View Series Model DifferencesC4000, Rear View Series Model ComponentsCLI Management Network Management ToolsSnmp MIB Management Page Initial Installation C2000 and C4000 1.0.x Hardware Guide Initial Installation Before You Begin Unpacking and Inspecting the C-series PlatformContacting Juniper Networks Inspecting System Components and AccessoriesUnpacking the Units If You Detect or Suspect DamageFreestanding Installation Installing and Cabling the C-series PlatformPreparing the Equipment Racks Rack-Mounted InstallationInstallation Guidelines Installing the SystemCabling the Management Console Cabling the SystemCabling Ethernet Interfaces Cabling the System for PowerC2000, Front View Next Step Powering Up Powering Up the C-series PlatformModel LEDs Status LEDsSetting the Initial Configuration Configuration OverviewSetting Up Management Access and Logging Configuring the Juniper Networks Database Edit Root@host# set system host-name my-hostname Configuring Hostname and Domain ParametersConfiguring the System for Remote Access Configuring the System to Accept SSH and Telnet Connections Adding an Admin User Account Set the password of the user C2000 and C4000 1.0.x Hardware Guide Next Step Hardware Maintenance Procedures and Specifications Page Required Tools and Items Maintaining the SystemCleaning the System Removing and Installing a FanStoring Modules and Components Removing and Installing a Power Supply Module Removing and Installing a Hard Drive System Specifications C2000 Model SpecificationsC2000 Model Specifications C4000 Model Specifications C4000 Model SpecificationsSystem Specifications Page Series Platform Data Storage Managing RAID Disks on a C-series PlatformReplacing a Disk Managing Disks in a C-series PlatformViewing Information About Disks on a C-series Platform Reinitializing an Active DiskField Name Field Description Show disk status Output FieldsYour Preinstallation Responsibilities Installation Guidelines and RequirementsRegulatory Compliances Environmental RequirementsSafety Guidelines Mechanical Requirements Equipment Rack RequirementsProper Rack Installation Space RequirementsCabling Recommendations Product Reclamation and Recycling Program Hardware Compliance Federal Communications Commission FCC StatementFCC Requirements for Consumer Products Avis CS-03 dIndustrie Canada Industry Canada Notice CS-03C. Explanatory Notes Equipment Attachment Limitations EC Declaration of Conformity Return Procedure Contacting Customer Support and Returning HardwareContacting Customer Support Information You Might Need to Supply to Jtac Locating Component Serial NumbersReturning Products for Repair or Replacement Tools and Parts RequiredPacking Instructions for Returning a Chassis Remove the chassis from the rack Declaration of Conformity Declaration of ConformityPage Index C2000 and C4000 1.0.x Hardware Guide Index Compliance Manuals
Top Page Image Contents