Hitachi WH14DM OM instruction manual Disconnect battery charger from the receptacle

Page 14

English

(3)Regarding recharging time (At 68°F (20°C)) In approx. 60 minutes.

NOTE:The charging time may vary according to temperature and power source voltage.

4. Disconnect battery charger from the receptacle.

CAUTION:

●Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5.Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

●When the battery charger has been continuosly used, the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging.

●If the battery is rechraged when it is warm due to battery use or exposure to sunlight, the pilot lamp may light in green.

The battery will not be recharged. In such a case, let the battery cool before charging.

●When the pilot lamp flikers rapidly in red (at 0.2–second intervals), check for and take out any foreign objects in the charger’s battery installation hole. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.

●Since the built-in micro computer takes about 3 seconds to confirm that the battery being charged with UC14YF2 is taken out, wait for a minimum of 3 seconds before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1)Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter.

(2)Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Avertissement AdvertenciaContents Important Safety Information Meanings of Signal WordsSafety General Safety Rules for ALL Battery Operated ToolsEnglish Specific Safety Rules Never operate without all guards in placeImportant Safety Instructions for Battery Charger 100 150 Make Them Available to Other Users Owners of this Tool Name of Parts Functional DescriptionModel Cordless Impact DriverBattery Charger UC 14YF2 SpecificationsBattery Charger UC14YF2 Insert the plug of battery charger into the receptacle Assembly and OperationRemoval and Installation Method of Battery ApplicationsInsert the battery to the battery charger ChargingDisconnect battery charger from the receptacle Remove the battery from the battery chargerOperation Using the light equipped hookBefore USE English Removing the bit Installing the bitSwitch operation Tightening and loosening screwsResting the unit after continuous work Operational CautionsNumber of screw tightenings possible Tightening torqueUse a tightening time suitable for the screw Bolt Steel plate Thickness t NutMaintenance and Inspection Service parts list Disposal of the exhausted battery StorageService and repairs Check for DustBattery AccessoriesStandard Accessories Wood working drill bit Code No Phillips bitHexagonal socket Drill chuck adapter set Code No Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Conserver CES InstructionsAvertissement Regles DE Securite Specifiques Manipuler l’outil motorisé avec précaution Intensité nominale d’entrée CA ampères Français Français NOM DES Parties Description FonctionnelleModele Visseuse à percussion à batterieChargeur de batterie UC14YF2 Utilisations Méthode DE Retrait ET D’INSTALLATION DE LA BatterieAssemblage ET Fonctionnement Méthode DE RechargeInsérer la batterie dans le chargeur de batterie RechargeDébrancher le chargeur de batterie de la prise Retirer la batterie du chargeur de batterieUtilisation du crochet avec lampe Avant L’UTILISATIONUtilisation Remarque Retrait de la mèche Vérifiez si la batterie a été correctement InstalléeMise en place de la mèche Vérifiez le sens de rotationNombre de serrages d’écrous ou de vis possible Fonctionnement de l’interrupteurSerrage et desserrage des vis Couple de serrage Precautions DutilisationRepos de l’appareil après un travail continu Utiliser le couple de serrage adapté à chaque type de visBoulon Epaisseur de la Plaque d’acier t Ecrou Vérifier les vis Entretien ET InspectionVérifier l’état de la mèche Entretien du moteurMise au rebut d’une batterie usée Remplacement d’un balai en carboneVérifier s’il y a de la poussière RangementListe des pièces de rechange Batterie AccessoiresAccessoires Standard Foret pour le forage du bois N de Code Mèche PhillipsDouille hexagonale Jeu d’adaptateur de mandrin de foreuse N de Code Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad Guarde Estas InstruccionesAdvertencia Normas Específicos DE Seguridad Utilice la herramienta correctaNo limpie las partes de plástico con disolvente 25 7,5 100 150 Español Español Nomenclatura Descripción FuncionalModelo Atornillador de impacto a bateríaCargador de baterías UC 14YF2 EspecificacionesCargador de baterías UC14YF2 Método DE Extracción E Instalación DE LA Batería Montaje Y OperaciónAplicaciones Método DE CargaInserte la batería en el cargador de baterías CargaDesconecte el cargador de baterías del tomacorriente Extraiga la batería del cargador de bateríasEmpleo del gancho equipado con luz Antes DE LA UtilizaciónOperación Nota Instalación de la punta del atornillador Extracción de la brocaNúmero posible de aprietes Operación de conmutaciónApretado y aflojado de pernos Emplee el tiempo de apriete adecuado al tornillo Precauciones OperacionalesPar de apriete 1000 868 800 Comprobación de los tornillos Mantenimiento E InspecciónComprobación de las condiciones de la broca Mantenimiento de motorEliminación de las baterías agotadas Reemplazar el carbón de contactoComprobación del polvo AlmacenamientoLista de repuestos ModificacionesBatería AccesoriosAccesorios Estándar Broca para taladrar madera No. de código Broca PhillipsReceptáculo hexagonal para tuercas y pernos Juego adaptador de portabrocas No. de código English Hitachi Koki Canada Co
Top Page Image Contents