Bostitch BTC400LB instruction manual Maintenance, Replacement Parts, Problem Possible Cause

Page 11
• Check battery pack installation.
• Check battery pack charging requirements.
• Insert battery pack into
charger until green LED appears.
• Plug charger into a working outlet. Refer to “Important Charging Notes” for more details.
• Move charger and battery
pack to a surrounding air temperature of above 40 degrees F (4.5°C) or below 105 degrees F (+40.5°C).
•Allow battery pack to cool down.
• Place on charger and allow to charge.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003.

Maintenance

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at www.bostitch.com. You can also order parts from your nearest Bostitch Factory Service Center or Bostitch Authorized Warranty Service Center. Or, you can call our Customer Care Center at (800) 262 2161.

Troubleshooting

Problem

Possible Cause

Possible Solution

• Unit will not start.

Battery pack not installed properly.

Battery pack not charged.

• Battery pack will not

• Battery pack not inserted into

charge.

charger.

 

• Charger not plugged in.

 

• Surrounding air temperature

 

too hot or too cold.

• Unit shuts off abruptly. • Battery pack has reached its maximum thermal limit.

• Out of charge. ( To maximize the life of the battery pack it is designed to shutoff abruptly when the charge is depleted.)

For assistance with your product, visit our website at www.bostitch.com for a list of service centers, or call the Bostitch Customer Care Center at (800) 262 2161.

11

Image 11
Contents 18v Work Area Safety Safety Guidelines DefinitionsPage Symbols Drill Safety WarningsDescription Catalog # Wire Size AWGREAD ALL Instructions Important Safety Instructions for Battery PacksHot/Cold Pack Delay Charging ProcedureCharger Diagnostics Bad Battery Important Charging Notes Safety Warnings and Instructions Drills Installing and Removing the Battery Pack From the Tool To install battery pack Insert battery packKeyless Chuck Figure G Trigger Switch & Forward/Reverse Button Figure DAdjusting Torque Control Figure E Dual Range Gearing Figure FDrilling in Metal Screw DrivingDrilling Drilling in WoodProblem Possible Cause MaintenanceReplacement Parts Accessories Three Year Limited Warranty Service and ReplacementPerceuse/Visseuse avec bloc-piles au lithium-ion Page Percez Consignes de sécurité Toujours Porter UN Équipement DE Protection Homologué SymbolesDescription Calibre AWGLire toutes les directives Pile en mauvais état Recommandations en matière de rangementFonctions de diagnostic du chargeur Procédure de chargeAvertissements de sécurité et directives perceuses Fonction de suspension du bloc-piles chaud/froidBloc-piles laissé dans le chargeur Remarques importantes pour le chargementRetrait du bloc-piles enfoncer le bouton de Commande de réglage du couple Figure EDétente et bouton de marche avant Marche arrière figure D Engrenage à deux vitesses figure FPerçage du métal Mode tournevisMode perçage Perçage du boisPièces de rechange Rangement des mèchesEntretien Maximiser la durée de vie du AccessoiresProblème Dépannage Solution possible Cause possible Entretien ET RéparationGarantie Limitée DE Trois ANS Remplacement DES Étiquettes D’AVERTISSEMENTPautas DE SEGURIDAD/DEFINICIONES Taladro/Destornillador con batería de Iones de litioPage Perforar Advertencias de seguridad Símbolos Descripción De cat Tamaño AWG del conductorLea todas las instrucciones Conserve Estas InstruccionesDiagnóstico del cargador Recomendaciones con respecto al almacenamientoProcedimiento de carga Notas importantes sobre la carga Batería en mal estadoRetraso por paquete caliente/frío Dejar la batería en el cargadorAjuste del control de torsión Figura E Interruptor disparador y botón de Avance/reversa Figura DTaladrado Engranaje de doble alcance Figura FPortabrocas sin llave Figura G DestornilladoLuz de trabajo de LED Taladrado en maderaTaladrado en metal Taladrado en mamposteríaPiezas DE Repuesto Mantenimiento Y Reparaciones MantenimientoGarantía Limitada DE Tres Anos AccesoriosPage June Catalog Numbers BTC400