Bostitch BTC400LB Service and Replacement, Accessories Three Year Limited Warranty

Page 12

Service and Replacement

All quality tools will eventually require servicing and/or replacement of parts. For information about Bostitch, its factory service centers or authorized warranty service centers, visit our website at www.bostitch.com or call our Customer Care Center at (800) 262 2161. All repairs made by our service centers are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by others.

You can also write to us for information at Bostitch, 701 E. Joppa Road, Towson, Maryland 21286 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, etc.).

ACCESSORIES

WARNING: Since accessories, other than those offered by Bostitch have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only Bostitch recommended accessories should be used with this product.

A complete line of accessories is available from your Bostitch Factory Service Center or a Bostitch Authorized Warranty Service Center. Please visit our Web Site www.bostitch.com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

Bostitch will repair or replace, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase for tools (two years for batteries). This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www. bostitch.com or call (800) 262-2161. This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, Bostitch tools are covered by our: 1 YEAR FREE SERVICE: Bostitch will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the performance of your Bostitch Power Tool for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained in the packaging, call the local company or see website for warranty information.

To register your tool for warranty service visit our website at www.bostitch.com

WARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call (800) 262-2161 for a free replacement.

Imported by Bostitch 701 E. Joppa Road Towson, Maryland 21286

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 18v Safety Guidelines Definitions Work Area SafetyPage Drill Safety Warnings SymbolsWire Size AWG Description Catalog #Important Safety Instructions for Battery Packs READ ALL InstructionsCharging Procedure Charger DiagnosticsBad Battery Hot/Cold Pack DelaySafety Warnings and Instructions Drills Installing and Removing the Battery Pack From the ToolTo install battery pack Insert battery pack Important Charging NotesTrigger Switch & Forward/Reverse Button Figure D Adjusting Torque Control Figure EDual Range Gearing Figure F Keyless Chuck Figure GScrew Driving DrillingDrilling in Wood Drilling in MetalMaintenance Replacement PartsProblem Possible Cause Service and Replacement Accessories Three Year Limited WarrantyPerceuse/Visseuse avec bloc-piles au lithium-ion Page Percez Consignes de sécurité Symboles Toujours Porter UN Équipement DE Protection HomologuéCalibre AWG DescriptionLire toutes les directives Recommandations en matière de rangement Fonctions de diagnostic du chargeurProcédure de charge Pile en mauvais étatFonction de suspension du bloc-piles chaud/froid Bloc-piles laissé dans le chargeurRemarques importantes pour le chargement Avertissements de sécurité et directives perceusesCommande de réglage du couple Figure E Détente et bouton de marche avant Marche arrière figure DEngrenage à deux vitesses figure F Retrait du bloc-piles enfoncer le bouton deMode tournevis Mode perçagePerçage du bois Perçage du métalRangement des mèches EntretienPièces de rechange Accessoires Problème Dépannage Solution possible Cause possibleEntretien ET Réparation Maximiser la durée de vie duRemplacement DES Étiquettes D’AVERTISSEMENT Garantie Limitée DE Trois ANSTaladro/Destornillador con batería de Iones de litio Pautas DE SEGURIDAD/DEFINICIONESPage Perforar Advertencias de seguridad Símbolos Tamaño AWG del conductor Descripción De catConserve Estas Instrucciones Lea todas las instruccionesRecomendaciones con respecto al almacenamiento Procedimiento de cargaDiagnóstico del cargador Batería en mal estado Retraso por paquete caliente/fríoDejar la batería en el cargador Notas importantes sobre la cargaInterruptor disparador y botón de Avance/reversa Figura D Ajuste del control de torsión Figura EEngranaje de doble alcance Figura F Portabrocas sin llave Figura GDestornillado TaladradoTaladrado en madera Taladrado en metalTaladrado en mampostería Luz de trabajo de LEDMantenimiento Piezas DE Repuesto Mantenimiento Y ReparacionesAccesorios Garantía Limitada DE Tres AnosPage Catalog Numbers BTC400 June

BTC400LB specifications

The Bostitch BTC400LB is a versatile and powerful cordless brad nailer designed for both professional contractors and DIY enthusiasts. Known for its reliability and user-friendly features, this tool simplifies the nailing process, making it an invaluable addition to any tool kit.

One of the standout features of the BTC400LB is its cordless design, powered by a robust lithium-ion battery. This technology not only eliminates the need for a bulky air compressor or cumbersome cords but also ensures consistent power delivery throughout your projects. The tool is equipped with a 20V MAX battery, which provides a higher voltage for increased power and efficiency, allowing users to work for extended periods without worrying about recharging.

The Bostitch BTC400LB boasts a lightweight and compact design, making it easy to maneuver in tight spaces and reducing user fatigue during extended use. At just over 5 pounds, it is designed for comfort, with an ergonomic handle that provides a secure grip, enhancing control while driving brads. This nailer is engineered to shoot 18-gauge brads ranging from 5/8-inch to 2 inches in length, making it suitable for various applications, such as trim work, molding, and cabinetry.

Another significant advancement in the BTC400LB is its adjustable depth control. This feature allows users to customize the depth of each nail, ensuring a flush finish every time. Additionally, the tool includes a tool-free jam release mechanism, which makes it easy to clear any jams that may occur during operation, minimizing downtime and enhancing productivity.

Safety is also a key consideration in the design of the Bostitch BTC400LB. The nailer comes with a safety tip that prevents accidental firing, ensuring that the tool is used safely and effectively. It also features an integrated LED work light, which illuminates your workspace, making it easier to see your work, especially in dimly lit environments.

Furthermore, the BTC400LB is designed with an easy-to-load magazine that holds up to 100 brads, reducing the frequency of reloads and allowing for uninterrupted work. Overall, the Bostitch BTC400LB combines advanced technology with practical features, making it an ideal choice for a wide range of nailing tasks, and solidifying its reputation as a reliable tool in both professional and hobbyist settings.
Top Page Image Contents