Bostitch BTC400LB Important Charging Notes, Safety Warnings and Instructions Drills

Page 8

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check current at receptacle by plugging in a lamp or other appliance

b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

c. Move charger and battery pack to a location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C).

d. If charging problems persist, take the tool, battery pack and charger to your local service center.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack.

Safety Warnings and Instructions: Drills

WARNING: Before using tool, read all instructions and cautionary markings on tool.

WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly with two hands to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting.

Operating Instructions

Installing and Removing the Battery Pack From the Tool

CAUTION: Make certain the lock-off button is engaged to prevent switch actuation before removing or installing battery.

To install battery pack: Insert battery pack

(7) firmly into tool until an audible click is heard as shown in Figure B.

To remove battery pack: Depress the battery release button (8) as shown in Figure C and pull battery pack out of tool.

B

C

8

Image 8
Contents 18v Safety Guidelines Definitions Work Area SafetyPage Drill Safety Warnings SymbolsWire Size AWG Description Catalog #Important Safety Instructions for Battery Packs READ ALL InstructionsCharging Procedure Charger DiagnosticsBad Battery Hot/Cold Pack DelaySafety Warnings and Instructions Drills Installing and Removing the Battery Pack From the ToolTo install battery pack Insert battery pack Important Charging NotesTrigger Switch & Forward/Reverse Button Figure D Adjusting Torque Control Figure EDual Range Gearing Figure F Keyless Chuck Figure GScrew Driving DrillingDrilling in Wood Drilling in MetalProblem Possible Cause MaintenanceReplacement Parts Service and Replacement Accessories Three Year Limited WarrantyPerceuse/Visseuse avec bloc-piles au lithium-ion Page Percez Consignes de sécurité Symboles Toujours Porter UN Équipement DE Protection HomologuéCalibre AWG DescriptionLire toutes les directives Recommandations en matière de rangement Fonctions de diagnostic du chargeurProcédure de charge Pile en mauvais étatFonction de suspension du bloc-piles chaud/froid Bloc-piles laissé dans le chargeurRemarques importantes pour le chargement Avertissements de sécurité et directives perceusesCommande de réglage du couple Figure E Détente et bouton de marche avant Marche arrière figure DEngrenage à deux vitesses figure F Retrait du bloc-piles enfoncer le bouton deMode tournevis Mode perçagePerçage du bois Perçage du métalPièces de rechange Rangement des mèchesEntretien Accessoires Problème Dépannage Solution possible Cause possibleEntretien ET Réparation Maximiser la durée de vie duRemplacement DES Étiquettes D’AVERTISSEMENT Garantie Limitée DE Trois ANSTaladro/Destornillador con batería de Iones de litio Pautas DE SEGURIDAD/DEFINICIONESPage Perforar Advertencias de seguridad Símbolos Tamaño AWG del conductor Descripción De catConserve Estas Instrucciones Lea todas las instruccionesDiagnóstico del cargador Recomendaciones con respecto al almacenamientoProcedimiento de carga Batería en mal estado Retraso por paquete caliente/fríoDejar la batería en el cargador Notas importantes sobre la cargaInterruptor disparador y botón de Avance/reversa Figura D Ajuste del control de torsión Figura EEngranaje de doble alcance Figura F Portabrocas sin llave Figura GDestornillado TaladradoTaladrado en madera Taladrado en metalTaladrado en mampostería Luz de trabajo de LEDMantenimiento Piezas DE Repuesto Mantenimiento Y ReparacionesAccesorios Garantía Limitada DE Tres AnosPage Catalog Numbers BTC400 June

BTC400LB specifications

The Bostitch BTC400LB is a versatile and powerful cordless brad nailer designed for both professional contractors and DIY enthusiasts. Known for its reliability and user-friendly features, this tool simplifies the nailing process, making it an invaluable addition to any tool kit.

One of the standout features of the BTC400LB is its cordless design, powered by a robust lithium-ion battery. This technology not only eliminates the need for a bulky air compressor or cumbersome cords but also ensures consistent power delivery throughout your projects. The tool is equipped with a 20V MAX battery, which provides a higher voltage for increased power and efficiency, allowing users to work for extended periods without worrying about recharging.

The Bostitch BTC400LB boasts a lightweight and compact design, making it easy to maneuver in tight spaces and reducing user fatigue during extended use. At just over 5 pounds, it is designed for comfort, with an ergonomic handle that provides a secure grip, enhancing control while driving brads. This nailer is engineered to shoot 18-gauge brads ranging from 5/8-inch to 2 inches in length, making it suitable for various applications, such as trim work, molding, and cabinetry.

Another significant advancement in the BTC400LB is its adjustable depth control. This feature allows users to customize the depth of each nail, ensuring a flush finish every time. Additionally, the tool includes a tool-free jam release mechanism, which makes it easy to clear any jams that may occur during operation, minimizing downtime and enhancing productivity.

Safety is also a key consideration in the design of the Bostitch BTC400LB. The nailer comes with a safety tip that prevents accidental firing, ensuring that the tool is used safely and effectively. It also features an integrated LED work light, which illuminates your workspace, making it easier to see your work, especially in dimly lit environments.

Furthermore, the BTC400LB is designed with an easy-to-load magazine that holds up to 100 brads, reducing the frequency of reloads and allowing for uninterrupted work. Overall, the Bostitch BTC400LB combines advanced technology with practical features, making it an ideal choice for a wide range of nailing tasks, and solidifying its reputation as a reliable tool in both professional and hobbyist settings.