Makita HR4013C instruction manual Selecting the action mode, Torque limiter, Indicator lamp

Page 6

The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work.

Selecting the action mode

CAUTION:

Do not rotate the change lever when the tool is

 

running. The tool will be damaged.

To avoid rapid wear on the mode change

 

mechanism, be sure that the change lever is

1

014880

1. Switch button

always positively located in one of the action mode

positions.

Hammer drilling mode

1

1.

Change lever

2.

Pointer

2

 

 

014022

For drilling in concrete, masonry, etc., rotate the change lever to thesymbol. Use a tungsten-carbide tipped bit.

Hammering mode (Switch trigger mode)

1

1.

Change lever

2.

Pointer

 

2

014024

For chipping, scaling or demolition operations, rotate the change lever to the symbol. Use a bull point, cold chisel, scaling chisel, etc.

Hammering mode (Switch button mode)

2

1.

Change lever

2.

Pointer

 

1

 

 

014023

For continuous chipping, scaling or demolition operations, rotate the change lever to the symbol.

The switch button projects out and lights in red. Use a bull point, cold chisel, scaling chisel, etc.

NOTE:

When using the tool in the symbol mode, the switch trigger does not work but only the switch button works.

Torque limiter

The torque limiter actuates when torque reaches a certain level. The motor disengages from the output shaft. When this happens, the bit stops turning.

CAUTION:

As soon as the torque limiter actuates, switch off the tool immediately. This helps to prevent premature wear of the tool.

Indicator lamp

1.

Power-ON

1

indicator lamp

 

(green)

2.

Service indicator

 

lamp (red)

2

014032

The green power-ON indicator lamp lights up when the tool is plugged in. If the indicator lamp does not light up, the mains cord or the controller may be defective.

When the indicator lamp lights up but the tool does not start even the tool is switched on, the carbon brushes may be worn out, or the controller, the motor or the ON/OFF switch may be defective.

If above symptoms occur, stop using the tool immediately and ask your local service center.

The red service indicator lamp lights up when the carbon brushes are nearly worn out to indicate that the tool needs servicing. After some period of use, the motor automatically shuts off.

6

Image 6
Contents Rotary Hammer Marteau Perforateur Martillo Rotativo Specifications Personal SafetyEnglish Original instructions AWG Rotary Hammer Safety Warnings SymbolsSwitch action Functional DescriptionSpeed change Selecting the action mode Indicator lampTorque limiter Installing or removing the bit AssemblyBit grease optional accessory Side handleDepth gauge Bit angle When chipping, scaling or demolishingOperation Hammer drilling operationMaintenance Blow-out bulb optional accessory LubricationChipping/Scaling/Demolition Connector Optional Accessories Warranty PolicyFrançais Mode d’emploi original SpécificationsPage Longueur totale du cordon en pieds Conservez CE Mode DemploiTableau 1. Gabarit minimum du cordon Intensité nominaleGâchette Description DU FonctionnementInterrupteur Bouton de mise en marcheSélection du mode de fonctionnement Changement de vitesseVoyant Mode martelage mode bouton de mise en marcheAssemblage Limiteur de coupleInstallation et retrait du embout Graisse rose accessoire en optionPoignée latérale Utilisation Jauge de profondeurPerçage avec martelage Lubrification Poire soufflante accessoire en optionEntretien Burinage/Ecaillage/DémolitionAvis Accessoires EN Option Politique de garantieEspecificaciones Español Instrucciones originalesIcft reduce el riesgo de descarga eléctrica Advertencia DE Seguridad Para USO DEL Martillo Rotativo Guarde Estas InstruccionesGatillo interruptor Descripción DEL FuncionamientoAccionamiento del interruptor Botón interruptorCambio de velocidad Selección del modo de accionamientoEmpuñadura lateral de asa EnsambleLimitador de torsión Luz indicadoraInstalación o extracción de la broca/cincel Empuñadura lateral de mangoGrasa para brocas accesorio opcional Ángulo de cincel al cortar, demoler o tallarOperación Calibrador de profundidadOperación de taladrado con percusión Cincelado/Tallado/Demolición MantenimientoSoplador Accesorio opcional LubricaciónAccesorios Opcionales Nota AvisoPolítica de garantía Page Page Advertencia