Miller Electric XR Control manual Directives, Standards

Page 5

Declaration of Conformity for

European Community (CE) Products

Note This information is provided for units with CE certification (see rating label on unit).

Manufacturer’s Name:

Manufacturer’s Address:

Declares that the product:

Miller Electric Mfg. Co.

1635 W. Spencer Street Appleton, WI 54914 USA

XR-Control

conforms to the following Directives and Standards:

Directives

Low Voltage Directive: 73/23/EEC

Electromagnetic Compatibility (EMC) Directive: 89/336/EEC

Machinery Directives: 89/392/EEC, 91/368/EEC, 93/C 133/04, 93/68/EEC

Standards

Arc Welding Equipment Part I: Welding Power Sources: IEC 60974-1

(September 1998 − Second Edition)

Arc Welding Equipment: Wirefeed Systems: IEC 974-5

(September 1997 − Draft Revision)

Degrees of Protection Provided By Enclosures (IP Code): IEC 529:1989

(November 1989 - First Edition)

Insulation Coordination For Equipment With Low-Voltage Systems:

Part I: Principles, Requirements and Tests: IEC 664-1: 1992

(October 1992 − First Edition)

Electromagnetic Compatibility, (EMC): EN 50199

(August 1995)

Torches And Guns For Arc Welding, EN 50078

European Contact: Mr. Danilo Fedolfi, Managing Director ITW WELDING PRODUCTS ITALY S.r.l. Via Privata Iseo 6/E

20098 San Giuliano Milanese, Italy

Telephone: 39(02)98290-1

Fax: 39(02)98290−203

dec_con1_11/02

Image 5

Contents Description OM-1594181 715ZProcesses From Miller to You Table of Contents Options and Accessories Warranty Standards DirectivesPage Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécurité+ + Rating Label For CE Products Specifications Symbols And DefinitionsPower DiameterDuty Cycle And Overheating Above 50 psi 345 kPa Do not use gas pressureAir-Cooled Feeder Connections Air-Cooled Gun Connections Water-Cooled Feeder Connections Water-Cooled Gun Connections Pin Plug Information Installing voltage sensing leadDigital Meter Display Meter Circuit Board SettingsVoltage Sensing Function Removing Top Cover Of Pistol Grip Gun Opening Top Cover Of XR-Edge GunInstalling Wire Spool It from unraveling Threading Welding Wire Through FeederFor XR-Edge Gun Threading Welding Wire Through GunFor Pistol-Grip Gun For Both GunsAdjusting Wire Feed Starting Speed Setting Switches For Preflow And Postflow Trigger hold actuation time range is from 0 to 4 seconds Adjusting Trigger Hold Actuation TimeControls − OperationInternal Controls Gun wire feed speedCoolant Supply For Water-Cooled Models Only Gun ControlsShielding Gas Sequence Of Gas Metal Arc Welding Gmaw − Continuous Or Spot Disconnect powerTo 6 Weeks MonthsWire size Feeder Drive Assembly MaintenancePost Pressure Roll w/Bearing Gun Drive Assembly Maintenance For An XR-Edge GunReplacing Head Tube Liner In XR-Edge Guns 030-1/16 wire sizeReplacing The Liner Turn Off welding power source and wire feederChanging Gun Contact Tip Replacing Or Cleaning Gun Drive Roll In Pistol-Grip GunsReplacing Head Tube Liner In Pistol-Grip Guns Removing Diffuser In Air And Water-Cooled Pistol-Grip Guns Replacing Hub Assembly Turn Off Wire Water Flow Switch Optional For Water-Cooled ModelsOverload Protection Engine WeldingDisconnect power before troubleshooting TroubleshootingTrouble Remedy Shielding gas does not flowOM-1594 − Electrical Diagrams 218 814-B Circuit Diagram For XR Edge Gun OM-1594 − Parts List MP1 Motor & Wire Drive Motor & Wire Drive -1Item Panel, Front w/Components Water-Cooled Model Illustrated Panel, Front w/Components -1Item Exploded View Of XR-Edge Gun Part Description Quantity Part Description Barrel Assembly Of XR-Edge Gun Exploded View Of Pistol-Grip Gun 214 166 Barrel Assembly Of Pistol-Grip Gun XR-A Spoolmatic Head Tube NumberXR-A Edge Head Tube XR-W Edge Head TubeExtra Heavy Duty FasTiptContact Tips Consumables Flowchart NozzlesHeavy Duty FasTiptContact Tips Value Multi−Turn Contact Tips Consumables Flowchart Tapered FasTipt Contact TipsGas Diffusers InsulatorsStart Your Professional Welding Career Now Page Support ServiceMiller Electric Mfg. Co Owner’s Record