Bosch Power Tools cordless hammer manual Maintenance, Accessories, Batteries

Page 13
! WARNING

BM 1619929426 8/01 8/2/01 1:19 PM Page 13

Maintenance

Service

!WARNING NO USER SERVICEABLE PARTS INSIDE. Preventive

maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recom- mend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station. SERVICEMEN: Disconnect tool and/or charger from power source before servicing.

BATTERIES

Be alert for battery packs that are nearing their end of life. Battery packs typically last from 500 to 1000 charges. If you notice decreased tool performance or significantly shorter running time between charges then it is time to replace the battery pack. Failure to do so can cause the tool to operate improperly or damage the charger.

Long term battery storage should be in the discharged state. Battery packs last longer and re-charge better when they are stored discharged. Remember to fully re- charge battery packs before using after prolonged storage.

TOOL LUBRICATION

Your Bosch tool has been properly lubricated and is ready for use. It is recommended that

tools with gears be regreased with a special gear lubricant yearly.

D.C. MOTORS

The motor in your tool has been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend it be examined every six months. Only a genuine Bosch replacement motor specially designed for your tool should be used.

Cleaning

!WARNING To avoid accidents, always disconnect the

tool and/or charger from the power supply before cleaning. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through opening.

Certain cleaning agents ! CAUTION and solvents damage

plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Accessories

If an extension cord is necessary, a cord with adequate size conductors that is capable

of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3- wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS

120 VOLT ALTERNATING CURRENT TOOLS

Tool’s

Cord Size in A.W.G.

Wire Sizes in mm2

Ampere

 

 

 

 

 

 

 

 

Cord Length in Feet

Cord Length in Meters

Rating

 

25

50

100

150

15

30

60

120

3-6

 

 

 

 

 

 

 

 

18

16

16

14

.75

.75

1.5

2.5

6-8

18

16

14

12

.75

1.0

2.5

4.0

8-10

18

16

14

12

.75

1.0

2.5

4.0

10-12

16

16

14

12

1.0

2.5

4.0

—

12-16

14

12

—

—

—

—

—

—

 

 

 

 

 

 

 

 

 

360˚ Auxiliary Handle*

(* =

standard equipment)

Depth Gauge*

(** =

optional accessories)

Carrying Case*

 

 

3-Jaw Chuck**

 

 

Straight Chuck SDS Adaptor**

 

 

-13-

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Importante For All Battery Operated Tools General Safety RulesService Cordless Rotary Hammer Safety RulesBattery/Charger NICKEL-METAL Hydride Batteries NICKEL-CADMIUM BatteriesSymbols SDS Functional Description and SpecificationsOperating Instructions Installing Accessories Battery Charged Condition IndicatorDRILL/HAMMER Drill Selection Dial 10 20% 20 40% 40 60% 60 80%Releasing and Inserting Battery Pack Removing AccessoriesCharging Battery Pack Important Charging Notes INDICATORS, Symbols and MeaningDrilling Metal Drilling Wood or PlasticDrilling Masonry Accessories MaintenanceBatteries Aire de travail Consignes générales de sécurité Pour tous les outils à pileSécurité électrique Utilisation et entretien des outilsRéparation Consignes de sécurité pour le marteau rotatif sans cordonLe plomb provenant des peintures à base de plomb Chargeur de pileProvoquer un incendie ou des blessures Entretien des pilesPiles NICKEL-CADMIUM Piles NICKEL-HYDRURE DE MétalTours ou mouvement alternatif par SymbolesPosition. Un nombre plus élevé signifie Une vitesse plus grandeNuméro de modèle Description fonctionnelle et spécificationsType de tige Temps de chargeConsignes de fonctionnement Cadran DE Sélection DE PERCEUSE/PERCEUSE À Percussion Pose DE L’ÉQUIPEMENT AccessoireTémoin DE Pile Chargée Retrait ET Insertion DU BLOC-PILE Dépose DE L’ÉQUIPEMENT AccessoireCharge DU BLOC-PILE Remarques Importantes Concernant LA Charge TÉMOINS, Symboles ET SignificationPerçage À Travers LA Maçonnerie Perçage Dans LE MétalAccessoires MaintenanceEntretien NettoyageSeguridad eléctrica Area de trabajoSeguridad personal Utilización y cuidado de las herramientasServicio Normas de seguridad para martillos giratorios sin cordónBatería/cargador Baterias DE NIQUEL-CADMIO Cuidado de las bateríasCadmio Ni-Cd indica que S-B Baterias DE NIQUEL-HIDRURO MetalicoCon aislamiento doble SímbolosDe Ni-Cd Número de modelo Descripción funcional y especificacionesEstilo de cuerpo Tiempo de cargaInstrucciones de funcionamiento Indicador DE Estado DE Carga DE LA Bateria Dial DE Seleccion DE TALADRO/TALADRO DE PercusionInstalacion DE Accesorios Arrancar la herramienta accidentalmenteSuelta E Introduccion DEL Paquete DE Baterias Remocion DE AccesoriosCarga DEL Paquete DE Baterias Notas Importantes Para Cargar INDICADORES, Simbolos Y SignificadoTaladrado DE Metal Taladrado DE Madera O PlasticoTaladrado DE Mamposteria Accesorios MantenimientoLimpieza BM 1619929426 8/01 8/2/01 119 PM BM 1619929426 8/01 8/2/01 119 PM Limited Warranty of Bosch Portable and Benchtop Power Tools
Top Page Image Contents