Bosch Power Tools 1380SLIM-2P, 1380 SLIM manual Wire Brush Operations

Page 14

BM 2610007691 12-09:BM 2610007691 11-09 12/18/09 11:17 AM Page 14

SANDING TIPS

For best results, tilt the Disc Sander at a 10° to 15° angle while sanding so that only about 1" of the surface around the edge of the disc contacts the work.

If the disc (accessory) is held ! WARNING flat or the back edge of the

disc comes in contact with the work, a violent thrust to the side may result.

If sander is tilted too much, sanding action will be too great and a rough cut surface or gouging and snagging will result.

Guide the Disc Sander with crosswise strokes. Be careful not to hold the sander in one spot too long. Do not use a circular motion, as this makes swirl marks. Test before use on scrap stock.

Do not force or apply pressure when sanding. Use only the weight of the tool for pressure. Excess pressure actually slows the tool down. If faster stock removal is desired, change to a coarser grit disc.

Remove gummy paint from metal with an “open coat” disc. Sand until sparks start to appear, then stop and change to a “closed coat” disc to remove any remaining paint.

SANDING WOOD

When sanding wood the direction of the disc motion at the contact point should parallel the grain as much as possible. The rapid cut of discs and the swirl type scratch pattern they occasionally create generally prohibit their use for producing the final finish.

Scratches and circular marks are usually the result of using too coarse a grit. When changing to a finer grit, move across the sand- ing lines that were made by a previous coarser disc.

SANDING METAL

When sanding automobiles or appliances, wipe the metal clean with a non-flammable solvent or commercial cleaner to remove all wax and grease. By doing this first, the sanding discs will sand better and last longer.

For heavy duty work, use a coarse grit disc first. Follow-up with a medium grit to remove scratches. To produce smooth finish, use fine grit disc.

Wire Brush Operations

Wire brushes are intended to “clean” structural steel, castings, sheet metal, stone and concrete. They are used to remove rust, scale and paint.

Avoid bouncing and snagging ! WARNING the wire brush, especially

when working corners, sharp edges etc. This can cause loss of control and kick-back.

BRUSHING PRESSURE

1.Remember, the tips of a wire brush do the work. Operate the brush with the lightest

pressure so only the tips of the wire come in contact with the work.

2.If heavier pressures are used, the wires will be overstressed, resulting in a wiping action; and if this is continued, the life of the brush will be shortened due to wire fatigue.

3.Apply the brush to the work in such a way that as much of the brush face as possible is in full contact with the work. Applying the side or edge of the brush to the work will result in wire breakage and shortened brush life.

CORRECT:

Wire tips doing

the work.

WIRE WHEEL BRUSH

INCORRECT:

Excessive

pressure can

cause wire breakage.

WIRE CUP BRUSH

CORRECT:INCORRECT:

Wire tips doing

Excessive pressure

the work.

can cause wire

 

breakage.

-14-

Image 14
Contents Ver la página Leer antes de usarSee Save ALL Warnings Instructions for Future Reference General Power Tool Safety WarningsPower tool use and care Power Tool-Specific Safety Warnings BM 2610007691 12-09BM 2610007691 11-09 12/18/09 1117 AM Page Additional Safety Warnings Symbols Name Designation/ExplanationSymbols Angle Grinder Functional Description and SpecificationsSwitch Button Spindle Lock Grinding WheelLock NUT and Backing Flange AssemblyKeys Screw Notches Vibration Control Side HandleSpindle Type 1A Wheel Guard Backing Flange Lock NUT Spindle Type Wheel Guard Backing Flange Grinding Lock NUTStraight Grinding Wheels Operating Instructions Disc Grinding Wheels Grinding OperationsSanding Operations Grinding TipsWire Brush Operations Cleaning MaintenanceService Accessory storage & maintenanceAccessories Wheel Type Wheel Diameter Wheel Thickness Arbor SizeSécurité personnelle Sécurité du lieu de travailSécurité électrique Utilisation et entretien des outils électroportatifsEntretien Avertissements sur les rebonds et effets associés La meule Avertissements supplémentaires concernant la sécurité Utilisez un protège-main pendant le ponçage et le brossageSymboles Symbole Nom Désignation/ExplicationSymboles suite CLÉ ET Case DE Remisage Prises D’AIR Description fonctionnelle et spécificationsRectifieuse d’angle Blocage DE ’ARBRE Poignée LatéralePose DU Protecteur DE Meule Description fonctionnelle et spécifications suiteAssemblage Ergots VIS Encoches Écrou DE Blocage ET Bride DappuiBlocage Ensemble DE Meule a DisqueArbre Meule DE Type Bride Dappui Protecteur DE Meule Type Bride Dappui Meule DEConsignes de fonctionnement Travaux de meulage Travaux de ponçageTravaux à la brosse métallique Cordons de rallonge Rangement & maintenance des accessoiresEntretien NettoyageAccessoires Type de meuleSeguridad personal Seguridad del área de trabajoSeguridad eléctrica Servicio de ajustes y reparaciones Uso y cuidado de las herramientas mecánicasRetroceso y advertencias relacionadas BM 2610007691 12-09BM 2610007691 11-09 12/18/09 1117 AM Advertencias de seguridad adicionales Utilice el protector de la mano cuando lije y cepilleSímbolos Símbolo Nombre Designación/explicaciónSímbolos continuación Rueda DE Amolar Descripción funcional y especificacionesAmoladora angulare Accesorio opcional EnsamblajeDientes Tornillo Muescas Protector DE LA Mano OpcionalRueda DE Amolar DE Tipo 1A para cortarRuedas Abrasivas DE Tipo 1 Para Amoladoras Rectas EL Disco DE Lijar Instrucciones de funcionamientoZapata DE Soporte HusilloOperación de amolado Operaciones de lijadoOperaciones con cepillos de alambre Servicio MantenimientoCordones de extensión LimpiezaLa rueda AccesoriosTipo de Diámetro de Grosor de Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools