Black & Decker RP250 instruction manual Operation

Page 9

492778-00 RP250 Router 2/6/06 1:13 PM Page 9

•Set the edge guide to the required distance.

•Tighten the fixing screws (16).

ATTACHING THE DUST EXTRACTION ADAPTOR (FIG. C)

WARNING: Turn the router off and disconnect it from the power supply.

The dust extraction adaptor allows you to connect a vacuum cleaner to the tool.

• Connect the hose (17) of the vacuum cleaner to the adaptor (10).

OPERATION

WARNING: To prevent personal injury, always disconnect plug from power source before assembly, making adjustments or changing bits. Failure to do so could result in accidental starting and possible injury.

WARNING: To reduce the risk of injury, do not overload the tool. Let it work at its own pace.

• Carefully guide the cord in order to avoid accidentally cutting it.

ADJUSTING THE DEPTH OF CUT (FIG. D, E & F)

WARNING: Turn the router off and disconnect it from the power supply.

The depth of cut is the distance (X in figure D) between the depth stop bar (8) and the depth stop (18). The depth of cut can be set in two different ways as follows:

ADJUSTING THE DEPTH OF CUT USING THE SCALE (FIG. E)

WARNING: Turn the router off and disconnect it from the power supply.

•Install the router bit as described previously.

•Loosen the locking screw (19).

•Pull the plunge lock lever (4) up.

•Plunge the router down until the router bit touches the workpiece.

•Push the plunge lock lever (4) down.

•Move the pointer (20) in the zero position on the scale (9).

•Add the desired depth of cut to the starting position.

•Move the depth stop bar (8) to the calculated position on the scale.

•Tighten the locking screw (19).

•Fine adjust using the adjusting knob (21).

•Pull the plunge lock lever (4) up and let the router return to its original position.

•After switching the router on, plunge it down and make the desired cut.

ADJUSTING THE DEPTH OF CUT USING A PIECE OF WOOD (FIG. F)

WARNING: Turn the router off and disconnect it from the power supply.

•Fit the router bit and plunge the router down as described above.

•Pull the depth stop bar (8) up.

•Place a piece of wood with a thickness equal to the desired depth of cut between the depth stop (17) and the depth stop bar (8).

•Tighten the locking screw (19).

•Fine adjust using the adjusting knob (21).

•Remove the piece of wood.

•Pull the plunge lock lever (4) up and let the router return to its original position.

•After switching the router on, plunge it down and make the desired cut.

ADJUSTING THE TURRET DEPTH STOP (FIG. G)

WARNING: Turn the router off and disconnect it from the power supply.

After turning the turret depth stop to the desired setting, you can fine-adjust the depth stop to be used. If you want to make several cuts with a different depth of cut, adjust each of the depth stops.

• Turn the depth stop screw (22) up or down as required using a screwdriver.

ELECTRONIC SPEED CONTROL DIAL

The speed of your router is variable. Use the electronic speed control dial (3) to produce uniform cutting results in wood, plastics and aluminum. Use the lower settings for large diameter cutters and the higher settings for small diameter cutters.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents VEA EL Español EN LA Contraportada Before Returning this Product For ANY Reason Please CallWork Area Safety Electrical SafetyPersonal Safety Power Tool USE and Care ServiceSpecific Safety Rules Motor Features 492778-00 RP250 Router 112 PM 112 PM Installing Installing and Removing a Router BIT FIG. aRemoving Attaching the Edge Guide FIG. BOperation Switching on and OFF Using a Straight Edge AS a Guide FIG. HUsing the Router Using the Router with Dust ExtractionAccessories MaintenanceService Information Router Bits FIG. K not IncludedFull TWO-YEAR Home USE Warranty Mode ’EMPLOI Sécurité EN Matière D’ÉLECTRICITÉ Sécurité DU Lieu DE TravailUtilisation ET Entretien D’UN Outil Électrique Sécurité PersonnelleRègles DE Sécurité Spécifiques RéparationMoteur Profondeur Échelle de profondeur de Coupe Caractéristiques492778-00 RP250 Router 113 PM 113 PM Insertion ET Retrait D’UNE Fraise FIG. a AssemblageInsertion Fixation DU Guide DE Chant FIG. BRéglage DE LA Profondeur DE Coupe FIG. D, E ET F Réglage DE LA Profondeur DE Coupe SUR L’ÉCHELLE FIG. ERéglage DE LA Butée D’ARRÊT DE LA Tourelle FIG. G Utilisation D’UNE Règle Droite Comme Guide FIG. H Molette DE Contrôle Électronique DE LA VitesseMise EN Marche ET Arrêt Utilisation DE LA Toupie DéfonceuseConseils Pour UNE Utilisation Optimale Fraises DE Toupie FIG. K NON ComprisesEntretien Accessoires Manual DE Instrucciones Seguridad Eléctrica Seguridad EN EL Área DE TrabajoUSO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalNormas DE Seguridad Específicas MantenimientoReciprocaciones por minuto Características 492778-00 RP250 Router 113 PM 113 PM Colocación Y Extracción DE LA Broca DE LA Rebajadora FIG. a ColocaciónAcople DE LA Guía DE Borde FIG. B Anexe AL Adaptador Para Extracción DE Polvo FIG. C OperaciónAjuste DE LA Profundidad DE Corte FIG. D, E Y F Ajuste DE LA Profundidad DE Corte Mediante LA Escala FIG. EUtilice UNA Regla Como Guía FIG. H Configuración DE LA VelocidadEncendido Y Apagado USO DE LA RebajadoraConsejos Para Optimizar EL USO USO DE LA Rebajadora CON UN Extractor DE PolvoBrocas Para Rebajadora FIG. K no Incluidas AplicaciónProblema Causa posible Solución posible Detección DE ProblemasImportante AccesoriosCULIACAN, SIN MONTERREY, N.L Garantía Completa DE DOS Años Para USO DomésticoGUADALAJARA, JAL PUEBLA, PUE492778-00 RP250 Router 2/6/06 113 PM
Top Page Image Contents