Hitachi SV 12SG instruction manual Orbital Sander Operation, How to hold the orbital sander

Page 12

English

ORBITAL SANDER OPERATION

WARNING: Never apply water or grinding fluid when sanding. This could result in electrical shock.

1. How to hold the orbital sander

While gripping the housing, lightly press the sander against the surface to be sanded so that the sanding paper uniformly contacts the surface, as shown in Fig. 6. DO NOT apply excessive pressure to the sander while sanding. Excessive pressure may cause overload of the motor, reduced service life of the sanding paper, and lowered sanding or polishing efficiency.

2.	How to move the orbital sander
	For optimum operating efficiency,
	alternately move the sander forward and
	backward at a constant speed and balance.
3.	Switching the sander ON and OFF	Fig. 6
	The power can be turned on by setting the
	lever to ON (1) and turned off by setting the
	lever to OFF (0).

NOTE:

Never turn the power switch ON when the sander is contacting the surface to be sanded. This is necessary to preclude damage to the material. The same applies when switching the power OFF.

CAUTION:

⬤lmmediately after use, always turn the sander off and unplug it.

⬤Since the sander may suck in dust and debris, be careful not to place it where there is much dust and debris when it is still spinning right after use.

12

Image 12

Contents Avertissement AdvertenciaContents Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Never use a tool which is defective or operating abnormally Do not wipe plastic parts with solventMake Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationSpecifications Functional DescriptionName of Parts Assembly and Operation ApplicationsPrior to Operation Installing the sanding paper Attaching and removing the dust bagHow to hold the orbital sander How to move the orbital sanderSwitching the sander on and OFF Orbital Sander OperationHOW to Install the Optional Accessories Bending the sanding paper Opening holes in the sanding paper with the punch plate Maintenance and Inspection Accessories Standard AccessoriesInformations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Regles Generale DE SecuriteConserver CES Instructions Avertissement Lire et coxmprendre toutes les instructionsFrançais Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesGarder propres les évents d’air du moteur Utiliser l’outil motorisé à la tension nominaleNe pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesAvant L’UTILISATION Fixation de la toile émeri Fixation et retrait du sac à poussièreUtilisation DE LA Ponceuse Orbitale Comment tenir la ponceuse orbitaleComment déplacer la ponceuse orbitale Mise en Marche et Arret de la ponceuseInstallation DES Accessoires EN Option Mise en place du papier de verre Pliage du papier de verreLe papier de verre pourrait être endommagé Français Entretien ET Inspection Accessoires Accessoires StandardFrançais Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Advertencia Lea y entienda todas las instruccionesEspañol Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móvilesUtilice la herramienta correcta Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Descripción Funcional NomenclaturaMontaje Y Operación AplicacionesAntes DE LA Operación Fijación del papel de lija Fijación y extracción de la bolsa colectora de polvoUtilización DE LA Lijadora Orbital Encendido y apagado de la lijadoraMontaje DE LOS Accesorios Opcionales Instalación del papel de lija Español Mantenimiento E Inspección Accesorios Accesorios EstándarEspañol Page 626VVC2PS2L Hitachi Koki Canada Co