Hitachi SP18VA instruction manual Assembly and Operation, Applications, Prior to Operation

Page 10

English

ASSEMBLY AND OPERATION

APPLICATIONS

◯Sanding metal surfaces.

◯Preliminary sanding of metal surfaces before painting, rust removal, removing old paint before repainting.

◯Finishing woodwork, correcting projections of timbers from joints or assemblies.

◯Preliminary sanding of wood surfaces before applying paint.

◯Polishing or shining painted metal surfaces, such as those of automobiles, trains, elevators, refrigerators, sewing machines, washing machines, metal appliances, etc.

◯Polishing varnished surfaces of wooden furniture, etc.

◯Shining synthetic resin or ebonite products.

PRIOR TO OPERATION

1.Power source

Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate.

2.Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while the switch is in the ON position, the power tool will start operating immediately and can cause serious injury.

3.Extension cord

When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING:

Damaged cord must be replaced or repaired.

4.Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard.

10

Image 10

Contents Advertencia AvertissementPolisseuse/lustruse électronique Table DES Matieres ContentsÍndice Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Never use a tool which is defective or operating abnormally Do not wipe plastic parts with solventMake Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationFunctional Description Name of PartsApplications Assembly and OperationPrior to Operation Electronic Sander Polisher Operation For use as a Polisher For use as a SanderFor use as a Polisher Using the backing pad Fig Using the rubber pad optional accessory FigFor use as a Sander Fig Service and repairs Maintenance and InspectionCleaning lock pin section Inspecting the screwsUse of any accessories other than those mentioned below or AccessoriesStandard Accessories DamageInformations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTConserver CES Instructions SecuriteRegles Generale DE Securite Avertissement Lire et coxmprendre toutes les instructionsSécurité personnelle Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesUtiliser l’outil motorisé à la tension nominale Manipuler l’outil correctementGarder propres les évents d’air du moteur Ne pas essuyer les parties en plastique avec du solvantFrançais Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle SpecificationsNOM DES Parties Interrupteur d’alimentation Avant L’UTILISATIONSource d’alimentation Cordon prolongateurVérifier la tige de verrouillage Fonctionnement DE LA Polisseuse Ponceuse ÉlectroniqueVérification des conditions d’environnement Fixation de la poignée à boucleUtilisation comme polisseuse Utilisation comme ponceuseAppuyer sur la tige de verrouillage pour Utilisation du plateau en caoutchouc Fig Inspection des balais en carbone Fig Entretien ET InspectionInspection des vis Nettoyage de la section de la tige de verrouillageAccessoires Accessoires StandardInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónGuarde Estas Instrucciones SeguridadNormas Generales DE Seguridad Advertencia Lea y entienda todas las instruccionesEspañol No toque Nunca las piezas móviles Normas Y Símbolos Específicos DE SeguridadUtilice la herramienta correcta Maneje con cuidado las herramientas eléctricas Maneje correctamente la herramientaNo limpie las partes de plástico con disolvente Español Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FuncionalEspecificaciones Aplicaciones Montaje Y OperaciónAntes DE LA Operación Confirme el pasador de bloqueo Operacíon DE LA PULIDORA/LIJADORA ElectrónicaConfirme las condiciones del medio ambiente Fijación de la empuñadura en anilloPara utilizarla como lijadora PrecauciónUtilización de la almohadilla de caucho Accesorio opcional FigPara utilizarla como lijadora Fig Inspección de la escobillas Fig Mantenimiento E InspecciónInspección de los tornillos Limpieza de la sección del pasador de bloqueoAccesorios Accesorios EstándarPage Hitachi Koki Canada Co