Hitachi SP18VA instruction manual English

Page 5

English

(3)Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

(4)Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

(5)Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

(6)Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or ear plugs must be used for appropriate conditions.

4.Tool Use and Care

(1)Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

(2)Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

(3)Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

(4)Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.

(5)Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

(6)Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

(7)Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. If damaged, have the tool serviced by a HITACHI authorized service center before using. Many accidents are caused by poorly maintained tools.

(8)Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used with another tool.

5.Service

(1)Tool service must be performed only by a HITACHI authorized service center. Service or maintenance performed by unqualified personnel could result in a risk of injury.

(2)When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instruction may create a risk of electric shock or injury.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Polisseuse/lustruse électronique AvertissementAdvertencia Índice ContentsTable DES Matieres Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Never use a tool which is defective or operating abnormallyDouble Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolName of Parts Functional DescriptionPrior to Operation Assembly and OperationApplications Electronic Sander Polisher Operation For use as a Sander For use as a PolisherUsing the rubber pad optional accessory Fig For use as a Polisher Using the backing pad FigFor use as a Sander Fig Cleaning lock pin section Maintenance and InspectionService and repairs Inspecting the screwsStandard Accessories AccessoriesUse of any accessories other than those mentioned below or DamageSignification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéRegles Generale DE Securite SecuriteConserver CES Instructions Avertissement Lire et coxmprendre toutes les instructionsSécurité personnelle NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesGarder propres les évents d’air du moteur Manipuler l’outil correctementUtiliser l’outil motorisé à la tension nominale Ne pas essuyer les parties en plastique avec du solvantFrançais Double Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties SpecificationsDescription Fonctionnelle Source d’alimentation Avant L’UTILISATIONInterrupteur d’alimentation Cordon prolongateurVérification des conditions d’environnement Fonctionnement DE LA Polisseuse Ponceuse ÉlectroniqueVérifier la tige de verrouillage Fixation de la poignée à boucleUtilisation comme ponceuse Utilisation comme polisseuseAppuyer sur la tige de verrouillage pour Utilisation du plateau en caoutchouc Fig Inspection des vis Entretien ET InspectionInspection des balais en carbone Fig Nettoyage de la section de la tige de verrouillageAccessoires Standard AccessoiresSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Advertencia Lea y entienda todas las instruccionesEspañol Utilice la herramienta correcta Normas Y Símbolos Específicos DE SeguridadNo toque Nunca las piezas móviles No limpie las partes de plástico con disolvente Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas Español Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FuncionalNomenclatura Antes DE LA Operación Montaje Y OperaciónAplicaciones Confirme las condiciones del medio ambiente Operacíon DE LA PULIDORA/LIJADORA ElectrónicaConfirme el pasador de bloqueo Fijación de la empuñadura en anilloPrecaución Para utilizarla como lijadoraAccesorio opcional Fig Utilización de la almohadilla de cauchoPara utilizarla como lijadora Fig Inspección de los tornillos Mantenimiento E InspecciónInspección de la escobillas Fig Limpieza de la sección del pasador de bloqueoAccesorios Estándar AccesoriosPage Hitachi Koki Canada Co
Top Page Image Contents