Hitachi SP18VA Maintenance and Inspection, Inspecting the screws, Cleaning lock pin section

Page 15

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection.

1.Inspecting the screws

Regularly inspect all screws and ensure that they are properly tightened. Should any of the screws be loosened, retighten them immediately.

WARNING: Using this electronic sander polisher with loosened screws is extremely dangerous.

Wear limit

2. Inspecting the carbon brushes (Fig. 8)

The motor employs carbon brushes which are

43

consumable parts. Replace the carbon brush with a

 

new one when it becomes worn to its wear limit.

No. of carbon

Always keep carbon brushes clean and ensure that

 

they slide freely within the brush holders.

 

 

Fig. 8

CAUTION:

 

Using this electronic sander polisher with a carbon brush which is worn in excess of the wear limit will damage the motor.

NOTE: Use HITACHI carbon brush No. indicated in Fig. 8.

Replacing carbon brushes:

Remove the brush caps (Fig. 1) with a slotted screwdriver. The carbon brushes can then be easily removed.

3.Cleaning lock pin section

If the lock pin section becomes dirty, clean it at once.

4.Service and repairs

All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY.

15

Image 15
Contents Avertissement AdvertenciaPolisseuse/lustruse électronique Contents Table DES MatieresÍndice Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Never use a tool which is defective or operating abnormallyDouble Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolName of Parts Functional DescriptionAssembly and Operation ApplicationsPrior to Operation Electronic Sander Polisher Operation For use as a Sander For use as a PolisherUsing the rubber pad optional accessory Fig For use as a Polisher Using the backing pad FigFor use as a Sander Fig Inspecting the screws Maintenance and InspectionCleaning lock pin section Service and repairsDamage AccessoriesStandard Accessories Use of any accessories other than those mentioned below orSignification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéAvertissement Lire et coxmprendre toutes les instructions SecuriteRegles Generale DE Securite Conserver CES InstructionsSécurité personnelle NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesNe pas essuyer les parties en plastique avec du solvant Manipuler l’outil correctementGarder propres les évents d’air du moteur Utiliser l’outil motorisé à la tension nominaleFrançais Double Isolation Pour UN Fonctionnement Plus SUR Specifications Description FonctionnelleNOM DES Parties Cordon prolongateur Avant L’UTILISATIONSource d’alimentation Interrupteur d’alimentationFixation de la poignée à boucle Fonctionnement DE LA Polisseuse Ponceuse ÉlectroniqueVérification des conditions d’environnement Vérifier la tige de verrouillageUtilisation comme ponceuse Utilisation comme polisseuseAppuyer sur la tige de verrouillage pour Utilisation du plateau en caoutchouc Fig Nettoyage de la section de la tige de verrouillage Entretien ET InspectionInspection des vis Inspection des balais en carbone FigAccessoires Standard AccessoiresSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadAdvertencia Lea y entienda todas las instrucciones SeguridadNormas Generales DE Seguridad Guarde Estas InstruccionesEspañol Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móvilesUtilice la herramienta correcta Maneje correctamente la herramienta Maneje con cuidado las herramientas eléctricasNo limpie las partes de plástico con disolvente Español Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Descripción Funcional NomenclaturaEspecificaciones Montaje Y Operación AplicacionesAntes DE LA Operación Fijación de la empuñadura en anillo Operacíon DE LA PULIDORA/LIJADORA ElectrónicaConfirme las condiciones del medio ambiente Confirme el pasador de bloqueoPrecaución Para utilizarla como lijadoraAccesorio opcional Fig Utilización de la almohadilla de cauchoPara utilizarla como lijadora Fig Limpieza de la sección del pasador de bloqueo Mantenimiento E InspecciónInspección de los tornillos Inspección de la escobillas FigAccesorios Estándar AccesoriosPage Hitachi Koki Canada Co