Hitachi SP18VA instruction manual For use as a Polisher Using the backing pad Fig

Page 13

English

ASSEMBLING AND DISASSEMBLING THE WOOL BONNET AND SANDING DISC

WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle to avoid serious trouble.

●For use as a Polisher

<Using the backing pad (Fig. 4)>

(1)Press the lock pin to secure the spindle and tighten the backing pad by rotating the outer circumference.

(2)Adhere the wool bonnet (Hook & Loop type) attached by pressing it firmly against the backing pad. Align the respective centers when attaching. If not centered, vibration will result.

(3)To remove the wool bonnet, follow the above-mentioned procedure in reverse order.

Backing Pad

Fig. 4

Wool

Bonnet (Hook & Loop type)

Spindle

Lock Pin

<Using the rubber pad (optional accessory) (Fig. 5)>

(1)Insert the washer nut (optional accessory) through the rubber pad (optional accessory) and thread it onto the spindle.

(2)Press the lock pin to secure the spindle and tighten the washer nut with a wrench.

(3)Wrap the rubber pad with the hood of the wool bonnet (optional accessory) and firmly secure it by tying a string around it. Be sure the excess string is firmly tucked inside the wool bonnet to prevent it from flying out while polishing.

The unbalanced fitting of the wool bonnet may cause vibration (Fig. 6).

(4)To remove the wool bonnet, follow the above-mentioned procedure in reverse order.

Washer

Nut

Rubber

Pad

Fig. 5

Wool

Bonnet

Spindle

Lock Pin

Tuck the excess	Hood
string into
	Fig. 6

13

Image 13

Contents Advertencia AvertissementPolisseuse/lustruse électronique Table DES Matieres ContentsÍndice Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Never use a tool which is defective or operating abnormallyDouble Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolName of Parts Functional Description Applications Assembly and Operation Prior to Operation Electronic Sander Polisher Operation For use as a Sander For use as a PolisherUsing the rubber pad optional accessory Fig For use as a Polisher Using the backing pad FigFor use as a Sander Fig Cleaning lock pin section Maintenance and InspectionService and repairs Inspecting the screwsStandard Accessories AccessoriesUse of any accessories other than those mentioned below or DamageSignification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéRegles Generale DE Securite SecuriteConserver CES Instructions Avertissement Lire et coxmprendre toutes les instructionsSécurité personnelle NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesGarder propres les évents d’air du moteur Manipuler l’outil correctementUtiliser l’outil motorisé à la tension nominale Ne pas essuyer les parties en plastique avec du solvantFrançais Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle SpecificationsNOM DES Parties Source d’alimentation Avant L’UTILISATIONInterrupteur d’alimentation Cordon prolongateurVérification des conditions d’environnement Fonctionnement DE LA Polisseuse Ponceuse ÉlectroniqueVérifier la tige de verrouillage Fixation de la poignée à boucleUtilisation comme ponceuse Utilisation comme polisseuseAppuyer sur la tige de verrouillage pour Utilisation du plateau en caoutchouc Fig Inspection des vis Entretien ET InspectionInspection des balais en carbone Fig Nettoyage de la section de la tige de verrouillageAccessoires Standard AccessoiresSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Advertencia Lea y entienda todas las instruccionesEspañol No toque Nunca las piezas móviles Normas Y Símbolos Específicos DE SeguridadUtilice la herramienta correcta Maneje con cuidado las herramientas eléctricas Maneje correctamente la herramientaNo limpie las partes de plástico con disolvente Español Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FuncionalEspecificaciones Aplicaciones Montaje Y OperaciónAntes DE LA Operación Confirme las condiciones del medio ambiente Operacíon DE LA PULIDORA/LIJADORA ElectrónicaConfirme el pasador de bloqueo Fijación de la empuñadura en anilloPrecaución Para utilizarla como lijadoraAccesorio opcional Fig Utilización de la almohadilla de cauchoPara utilizarla como lijadora Fig Inspección de los tornillos Mantenimiento E InspecciónInspección de la escobillas Fig Limpieza de la sección del pasador de bloqueoAccesorios Estándar AccesoriosPage Hitachi Koki Canada Co