Schumacher PSW-22 owner manual Control Panel

Page 8

1.Carefully lay the charger on its front to prepare for assembly.

2.Assemble the foot (Item 6) using two ¼-20 screws (Item 5) and tighten securely.

3.Attach the two axle brackets (Item 1) using one 10-32 screw (Item 4) in each. The brackets should have one end hooked into the slot in the charger base. Be careful not to drop the brackets inside of the charger case. Do not completely tighten the screws (Item 4) at this time.

4.Slide the axle (Item 2) into the brackets (Item 1) until centered on the charger.

5.Slide one wheel (Item 3) onto the axle with the recessed hub facing out as shown.

6.Insert the pin (Item 8) through the axle hole.

7.Repeat this process for the other wheel and when both wheels have been pinned to the axle, finish tightening the two axle bracket screws (Item 4).

8.Snap the axle caps (Item 7) onto each wheel to cover the pin and axle.

9.Lift the charger upright so that it rests on the wheels and foot.

10.Remove the two top side screws (Item 9) from each side of the charger.

11.Verify that the foam handle grip (Item 12) is on the handle assembly (Item 10). Install it if needed.

12.Insert the fiberglass clamp rod (Item 11) into the pierced holes on the inside of the handle (Item 10).

13.Align the handle assembly (Item 10) with the charger and reinstall the side screws (Item 9). Do not over tighten.

14.The charger assembly is now complete. The battery clips can be clamped to the fiberglass rod (Item 11) for convenient storage.

15.Do not attach the clips to the foam area of the handle; this will damage the foam grip.

12

10

11

9

11.CONTROL PANEL

Note: Not all controls are available on all models.

Timer

•Timer Setting: The timer allows you to set a specified time for charging. After the timer expires, the charger stops charging your battery. The main function of the timer is to prevent over charging while allowing a battery time to obtain a satisfactory charge. To properly set the timer, you must know the size of the battery in ampere hours or reserve capacity in minutes and the state of charge. It is important that you determine the appropriate state of charge of your battery as specified in Section 13 and set the timer accordingly.

•Hold: This position defeats the timer function, allowing for continuous operation. Put the timer in the HOLD position when you want to charge more than 2¼ hours. Be sure to monitor the charging progress and stop it when the battery is charged. Not doing so may cause damage to your battery or may cause other personal property damage or personal injury.

• 8 •

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Manual Battery Charger Risk of Electric Shock or Fire Personal Precautions Risk of Explosive Gases Risk of Explosive GasesDC Connection Precautions Grounding and ac power cord connections Wheel Charger Assembly Instructions for PSW-2035 FeaturesAssembly Instructions Parts Tools Needed Control Panel Operating Instructions Charging Model PSW-2035 Model PSW-61224 employs a 7-position rotary switchBattery Load Tester Switch Model PSW-3060 only Using the Engine Start feature Charging Models PSW-22, PSW 2550, PSW-3060 and PSW-61224Using the Battery Voltage Tester Overview Using the Alternator Performance Tester OverviewMaintenance Instructions General Charging NotesCalculating Charge Time Storage InstructionsTroubleshooting Problem Possible Cause REASON/SOLUTION Problem Possible Cause REASON/SOLUTION Before Returning for Repairs Limited WarrantyWarranty not valid in Mexico Do not Return this Product to the Store Mount Prospect, IL Mail this card toBusiness Center Drive Inscription AU Programme DE Garantie Limitée DE 3 ANS EL Riesgo DE Descarga Eléctrica O Incendio Riesgo DE Gases Explosivos Precauciones Personales Riesgo DE Gases ExplosivosPrecauciones DE Conexión EN CC Conexiones a tierra y energía de CA Características RuedaPiezas Herramientas Necesarias Artí Piezas Herramientas Culo Necesarias Panel DE Control TemporizadorAmperímetro VoltímetroCarga Modelos PSW-22, PSW-2550, PSW-3060 y PSW-61224 Interruptor Selector de voltajeInstrucciones DE Operación Carga Modelo PSW-2035 Utilizar la función de encendido de motor Utilizar el probador de tensión de batería Visión generalNotas generales sobre la carga 13. Cálculo DE Tiempo DE Carga El método del gráficoInstrucciones DE Mantenimiento Instrucciones DE AlmacenajeLocalización Y Solución DE Problemas Posible Causa Problema Posible Causa Solución Antes DE Devolver a Reparaciones ¡NO LO Devuelva este producto a LA Tienda Risque DE Choc Électrique OU D’INCENDIE Risque DE GAZ Explosifs Précautions Personnelles Risque DE GAZ ExplosifsPrécautions SUR LA Connexion C.C Page Mise à la terre et cordon d’énergie CA Caractéristiques 110Pièces Outils Nécessaires Article Pièces Outils NécessairesPanneau DE Contrôle MinuterieAmpèremètre VoltmètreLe chargement Modèle PSW-2035 Sélecteur de tensionConsignes D’UTILISATION Utilisation du dispositif Aide-Démarrage Utilisation du testeur de tension de batterie Vue d’ensembleTester la performance de l’alternateur Vue d’ensemble Calcul DU Temps DE Chargement La méthode tableauConsignes D’ENTRETIEN Directives D’ENTREPOSAGETableau DE Dépannage Problème Cause Possible RAISON/SOLUTION Problème Cause Possible RAISON/SOLUTION Avant DE L’ENVOYER Pour Réparation Garantie Limitée Garantie n’est pas valide au Mexique
Top Page Image Contents