Sanyo KS3682, KS3082 instruction manual Remote Control Unit

Page 6

01_KS3682_EN.fm Page 6 Friday, February 12, 2010 12:26 PM

REMOTE CONTROL UNIT

Transmitter

When you press the buttons on the remote control unit, the mark appears in the display to transmit the setting changes to the receiver in the air conditioner.

Display

Information on the operating conditions is displayed while the remote control unit is switched on. If the unit is turned off, FLAP setting and FAN SPEED setting are not displayed.

LED CLEAN button

: If this button is pressed during DRY, COOL or FAN operation, the UV anti-bacterial unit is activated for 30 minutes and cleans the air blown from the air conditioner.

QUIET button

: When you press this button, the fan rotates slower than the fan speed setting to provide a quieter operating sound.

FAN SPEED selector button

: The air conditioner automatically decides the fan speeds.

: High fan speed

: Medium fan speed : Low fan speed

FLAP button

Press this button either to select the setting of the airflow direction to the auto. flap in each mode or one of the six possible positions manually or to select the sweep function which moves the flap up and down automatically. : Auto flap setting: If selected in a cooling or dry operation, the flap is

set at position (7) in the following chart.

: The airflow direction can be set manually. (six positions) : The flap moves up and down automatically.

NOTE

When you press the FLAP button, the air flow direction will be changed one by one as follows.

SWEEP

ON TIME/OFF TIME setting buttons

Advance button

Return button

No display: The timer does not operate.

: The air conditioner starts at the set time.

: The air conditioner stops at the set time.

: The air conditioner stops and starts, or starts and stops, at the set times every day. For details, see “SETTING THE TIMER”.

CANCEL button

SENSOR button

When you press this button (use a small-tipped object such as a ballpoint pen), the mark will appear at the display. And the room temperature is detected by the

sensor which is built into the indoor unit and the air conditioner is controlled accordingly.

NOTE

If the remote control unit is located near a heat source, such as a space heater or in direct sunlight, press the SENSOR button to switch to the sensor on the indoor unit.

ADDRESS switch

 

Temperature display selector button

 

The address switch changes to prevent mixing of signals from remote control units when two air conditioners are installed next to each other. Normally, the address switch is set to A. For more information, please contact the dealer where you made the purchase.

Normally, the tabs on the remote control unit should not be bent.

This switches the temperature display between °C and °F.

6

OI-150-6-EG

 

Image 6
Contents Mode D’EMPLOI KS3082 KS3682Features ContentsSafety Instructions Alert SymbolsInstallation Location Product InformationNames of Parts Unit Display and Operation ButtonRemote Control Unit Display SymbolsRemote Control Unit Mode selector button HR. Timer button 1-HOUR OFF TimerTemperature setting buttons Temp High Power buttonACL button Using the Remote Control UnitAir conditioner Indoor unit Receiver Remote control unit 16 mmOperation Operation with the Remote Control UnitAdjusting the Fan Speed Fan OnlyHigh Power Mode Night Setback ModeQuiet Mode Cooling and DRY ModeCooling Mode LED Clean ModeUnoccupied Mode Unoccupied Indication StatusSetting the Timer Special RemarksHow to set daily ON/OFF repeat timer How to set the OFF timeHow to set the on time 1030 pm 710 am 1100 am Present timeUsing the 1-HOUR OFF Timer Adjusting the Airflow DirectionTips for Energy Saving Care and Cleaning Cleaning the main unit and remote control unit How to install the air clean filterHow to clean the air clean filter Removing and remounting the front panelOperating Range TroubleshootingWired Remote Controller Trouble Possible Cause RemedyCaractéristiques Table DES MatièresInformations SUR LE Produit Symboles ’AVERTISSEMENTEmplacement D’INSTALLATION Conseils DE SécuritéNOM DES Pièces Télécommande Affichage SymbolesTélécommande On TIME/OFF TimeBouton de haute puissance High Power Bouton de temporisateur 1 heure 1 HR. TimerSélecteur de mode Mode CapteurBouton ACL Utilisation DE LA TélécommandeClimatiseur élément intérieur Récepteur Télécommande 32 x 5/8 4 x 16 mmRéglage de la vitesse du ventilateur Fonctionnement Avec TélécommandeFonctionnement Vitesse manuelle du ventilateurMode de fonctionnement à haute puissance Mode économie nocturneMode de silencieux Quiet En mode de refroidissement et séchage etEn mode de refroidissement Mode de voyant de nettoyage LED CleanMode Pièce inoccupée Unoccupied Indication de pièce inoccupée Fonction Pièce EtatRemarques Spéciales Réglage DU Temporisateur1030 p.m 710 a.m 1100 a.m ’heure actuelle Marche Arrêt Réglage du moment de mise à l’arrêtRéglage du moment de mise en marche Pour annuler une programmationEmploi DU Temporisateur 1 Heure Réglage DU Flux D’AIRConseils Pour Économiser L’ÉNERGIE Fonctionnement Sans Entretien ET NettoyageNettoyage du filtre de nettoyage d’air Installation du filtre de nettoyage d’airNettoyage de l’appareil principale et de la télécommande Dépose et remise en place du panneau avantPlage DE Températures DE Fonctionnement Télécommande FilaireGuide DE Dépannage Panne Cause possible RemèdeIshida Make up USレター 白ページ Ishida Make up USレター 白ページ Sanyo Ave., San Diego