Porter-Cable PC1800SS To Maintain Safe Tool Control, ON/OFF Slider Switch Figure E, Depth Guide

Page 10

90562807 PC1800SS rotary saw.qxd:??????-00 Cir Saw book 3/24/10 8:27 AM Page 10

•TO REMOVE BATTERY PACK: Depress the battery release button as shown in figure D and pull battery pack out of tool.

Operating Instructions

TO MAINTAIN SAFE TOOL CONTROL

D

•Make sure the work surface is free of nails or screws. Cutting into a nail or screw may cause the tool to jump, damaging the bit.

•Never operate the tool with one hand while holding the workpiece with the other hand. Always clamp the material and guide the tool with both hands.

•Do not cut material lying on a hard surface. Clearance behind material to be cut must be allowed for protruding bit.

•Disconnect battery from tool before making adjustments, changing bits, or cleaning tool.

•Do not start the tool with bit engaged in the material. The bit may grab the material.

ON/OFF SLIDER SWITCH (FIGURE E)

E

To start the motor, slide the on/off slider switch to “I”

position. To stop the motor, slide the switch to “O”

 

position.

 

 

 

DEPTH GUIDE

: Laceration Hazard. Turn off tool and remove battery before making any adjustments or removing/installing attachments or accessories.

Keep depth guide in place at all times during operation of the tool. For best results, adjust the guide using knobs to allow the bit to protrude about 1/8 in. past the material to be cut.

INSTALLING AND REMOVING THE BIT (FIGURES F, G)

: Laceration Hazard. Turn off tool and remove battery before making any adjustments or removing/installing attachments or accessories.

1.Remove the depth guide using the end of the supplied wrench as shown in figure F.

F

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Advertencia Léase Este Catalog NumberGeneral Power Tool Safety Warnings Specific Safety Rules Page LI-ION Battery Packs and Chargers Description Cat. # NI-CD Battery Packs and Chargers Description Cat. #Important Safety Instructions for Battery Chargers Important Safety Instruction for Battery Packs Charger Diagnostics Battery CAP InformationCharging Procedure BAD BatteryInstalling and Removing the Battery Pack from the Tool Problem Power LineLeaving the Battery in the Charger Important Charging NotesTo Maintain Safe Tool Control ON/OFF Slider Switch Figure EInstalling and Removing the BIT Figures F, G Depth GuideTo Change the Collet Never tighten the collet without a bit installedChanging the Collet General CuttingAssembling Circle Cutter Figure Cutting a Hole for AN Electrical OutletAttaching Circle Cutter Figure J Maintenance TroubleshootingUsing Circle Cutter Figure K Specialnotes for USE with Lithium BatteriesAccessories Three Year Limited WarrantyReplacement Parts Service and Repairs Rbrc SealHighway North Jackson, TN 888 DE Catalogue Page Page Consignes DE Sécurité Particulières Lignes Directrices EN Matière DE Sécurité Définitions Description De catDescription Fonctionnelle SymbolesCalibre AWG Conserver CES Directives Information Concernant LE Capuchon DU BLOC-PILE Directives DE Sécurité Importantes Pour LES BLOCS- PilesLire Toutes LES Directives Piles au LI-ION dans les bagages enregistrésProcédure DE Charge Recommandations EN Matière DE RangementFonctions DE Diagnostic DU Chargeur Pile EN Mauvais ÉtatRemarques Importantes Pour LE Chargement Insertion ET Retrait DU BLOC-PILES DE L’OUTILGuide DE Profondeur Sécurité ET Maîtrise DE L’OUTILInterrupteur Coulissant MARCHE/ARRÊT Figure E Pose ET Dépose DE LA Mèche Figures F, GNe jamais serrer la pince si aucune mèche n’est posée Remplacement DE LA Douille DE SerrageRemplacement DE LA Douille Coupes OrdinairesMonter LE Trépan Figure Électrique Figure HFixer LE Trépan Figure J Entretien LE Sceau SrprcmcUtiliser UN Trépan Figure K Pièces DE RechangeProblème Cause possible Solution possibleAccessoires DépannageRemplacement DES Étiquettes DʼAVERTISSEMENT Garantie Limitée DE Trois ANSCatálogo N Page Page Normas Específicas DE Seguridad Pautas DE SEGURIDAD/DEFINICIONES PeligroDescripción DE LAS Funciones Figura a Descripción De catSímbolos Tamaño AWG del conductor LEA Todas LAS Instrucciones Información Acerca DEL Protector DE LA BateríaDiagnóstico DEL Cargador Recomendaciones CON Respecto AL AlmacenamientoProcedimiento DE Carga Batería EN MAL EstadoDejar LA Batería EN EL Cargador Línea DE Potencia CON ProblemasNotas Importantes Sobre LA Carga Para Mantener UN Control Seguro Sobre Herramienta Interruptor Deslizante DE ENCENDIDO/APAGADO Figura ECuando reemplace las brocas, no coloque el lado de las Guía DE ProfundidadInstalación Y Extracción DE LA Broca Figuras F, G Ranuras dentro del collar. Esto puede romper la brocaCortes EN General Cambio DE MordazasPara Cambiar LA Mordaza Corte DE Hueco Para UNA Caja DE Tomacorriente Figura HColocación DEL Cortador Circular Figura J Montaje DEL Cortador Circular FiguraUSO DEL Cortador Circular Figura K Notas Especiales Paraeluso CON Baterías DE Litio Detección DE ProblemasAdaptador Para Aspiradoras Figura L MantenimientoPiezas DE Repuesto Mantenimiento Y Reparaciones Garantía Limitada DE Tres AñosAccesorios Catalog Number PC1800SS Reemplazo DE LAS Etiquetas DE AdvertenciaEspecificacionespcmvc March

90562807, PC1800SS specifications

The Porter-Cable PC1800SS, 90562807 is a powerful cordless drill that has garnered attention for its impressive features and versatility. Designed for both professionals and DIY enthusiasts, this tool excels in various drilling and fastening tasks, making it a valuable addition to any toolkit.

At the heart of the PC1800SS is its robust 18-volt lithium-ion battery, which provides a reliable and consistent power source. This battery technology not only enhances runtime but also ensures shorter charging times, allowing users to complete projects more efficiently. With a fully charged battery, users can expect an extended duration of use, making it ideal for prolonged tasks or larger projects.

One of the standout features of the Porter-Cable PC1800SS is its two-speed gear mechanism, which offers speeds of 0-350 RPM and 0-1,500 RPM. This flexibility allows users to easily switch between high torque settings for heavier tasks and fast speeds for drilling into softer materials. Additionally, the drill provides a 1/2-inch keyless chuck that makes changing bits quick and easy, saving valuable time during operation.

The tool also incorporates an LED light that illuminates the workspace, making it easier to work in dimly lit environments. This feature is particularly helpful for tasks that require precision and detail. Coupled with its ergonomic design, the PC1800SS ensures maximum comfort during use, minimizing fatigue even during extended periods of operation.

With a built-in belt hook, the Porter-Cable PC1800SS offers convenience and accessibility, allowing users to keep the drill nearby without needing to set it down frequently. This feature is appreciated by professionals who move around job sites or those working in tight spaces.

In summary, the Porter-Cable PC1800SS, 90562807 is a versatile cordless drill that combines power, convenience, and advanced technology. Its lightweight design, impressive battery life, two-speed settings, and integrated LED light make it a go-to tool for a myriad of applications. Whether tackling home improvement projects or professional contracting tasks, this drill proves its worth with every use. With Porter-Cable’s commitment to quality and durability, the PC1800SS is a reliable choice that continues to meet the needs of users across various skill levels.
Top Page Image Contents