Porter-Cable PC1800SS Cutting a Hole for AN Electrical Outlet, Assembling Circle Cutter Figure

Page 12

90562807 PC1800SS rotary saw.qxd:??????-00 Cir Saw book 3/24/10 8:27 AM Page 12

CUTTING A HOLE FOR AN ELECTRICAL OUTLET

H

(FIGURE H)

 

: Shock Hazard. Shut off all live

 

electric circuits to any areas where cut outs will be

 

made.

 

1. Push any wiring deeply into the outlet box to avoid

 

damage from the cutting bit.

 

2. Before hanging the sheet covering the outlet, mark the approximate location of the center of the outlet on the wall board. Check the cutting bit depth against the side of the board to be sure it will cut entirely through the material.

3.Tack the sheet in place with a few fasteners

avoiding the stud holding the outlet. This allows the wall board to flex slightly around the protruding fixture box.

4.Turn the tool on. Holding the tool firmly with both hands, plunge the bit straight into the center of the outlet.

5.Cut to the right until the edge of the box is touched. Pull out just enough for the bit to clear the edge of the box. Plunge in again holding the bit gently against the outside of the box.

6.Follow the outside of the box as shown keeping slight pressure against the box. This will minimize wandering and give you a clean precise cut.

7.Remove the waste and dust from the outlet. Finish fastening the sheet of wall board.

ASSEMBLING CIRCLE CUTTER (FIGURE I)

: Laceration Hazard. Turn off tool and remove battery before making any adjustments or removing/installing attachments or accessories.

1.Attach the handle and pivot knob as shown in figure I.

I

ATTACHING CIRCLE CUTTER (FIGURE J)

: Laceration Hazard. Turn off tool and remove battery before making any adjustments or removing/installing attachments or accessories.

1.Place adapter (A) under depth guide opening.

2.Place circle cutter arm (B) on top of depth guide.

3.Screw threaded washer (C) onto adapter to secure circle cutter arm (B).

J

C

 

B

 

A

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Advertencia Léase Este Catalog NumberGeneral Power Tool Safety Warnings Specific Safety Rules Page LI-ION Battery Packs and Chargers Description Cat. # NI-CD Battery Packs and Chargers Description Cat. #Important Safety Instructions for Battery Chargers Important Safety Instruction for Battery Packs Battery CAP Information Charging ProcedureCharger Diagnostics BAD BatteryProblem Power Line Leaving the Battery in the ChargerInstalling and Removing the Battery Pack from the Tool Important Charging NotesON/OFF Slider Switch Figure E Installing and Removing the BIT Figures F, GTo Maintain Safe Tool Control Depth GuideNever tighten the collet without a bit installed Changing the ColletTo Change the Collet General CuttingCutting a Hole for AN Electrical Outlet Assembling Circle Cutter FigureAttaching Circle Cutter Figure J Troubleshooting Using Circle Cutter Figure KMaintenance Specialnotes for USE with Lithium BatteriesThree Year Limited Warranty Replacement Parts Service and RepairsAccessories Rbrc SealHighway North Jackson, TN 888 DE Catalogue Page Page Consignes DE Sécurité Particulières Lignes Directrices EN Matière DE Sécurité Définitions Description De catSymboles Description FonctionnelleCalibre AWG Conserver CES Directives Directives DE Sécurité Importantes Pour LES BLOCS- Piles Lire Toutes LES DirectivesInformation Concernant LE Capuchon DU BLOC-PILE Piles au LI-ION dans les bagages enregistrésRecommandations EN Matière DE Rangement Fonctions DE Diagnostic DU ChargeurProcédure DE Charge Pile EN Mauvais ÉtatRemarques Importantes Pour LE Chargement Insertion ET Retrait DU BLOC-PILES DE L’OUTILSécurité ET Maîtrise DE L’OUTIL Interrupteur Coulissant MARCHE/ARRÊT Figure EGuide DE Profondeur Pose ET Dépose DE LA Mèche Figures F, GRemplacement DE LA Douille DE Serrage Remplacement DE LA DouilleNe jamais serrer la pince si aucune mèche n’est posée Coupes OrdinairesÉlectrique Figure H Monter LE Trépan FigureFixer LE Trépan Figure J LE Sceau Srprcmc Utiliser UN Trépan Figure KEntretien Pièces DE RechangeCause possible Solution possible AccessoiresProblème DépannageRemplacement DES Étiquettes DʼAVERTISSEMENT Garantie Limitée DE Trois ANSCatálogo N Page Page Normas Específicas DE Seguridad Pautas DE SEGURIDAD/DEFINICIONES PeligroDescripción De cat Descripción DE LAS Funciones Figura aSímbolos Tamaño AWG del conductor LEA Todas LAS Instrucciones Información Acerca DEL Protector DE LA BateríaRecomendaciones CON Respecto AL Almacenamiento Procedimiento DE CargaDiagnóstico DEL Cargador Batería EN MAL EstadoLínea DE Potencia CON Problemas Dejar LA Batería EN EL CargadorNotas Importantes Sobre LA Carga Para Mantener UN Control Seguro Sobre Herramienta Interruptor Deslizante DE ENCENDIDO/APAGADO Figura EGuía DE Profundidad Instalación Y Extracción DE LA Broca Figuras F, GCuando reemplace las brocas, no coloque el lado de las Ranuras dentro del collar. Esto puede romper la brocaCambio DE Mordazas Para Cambiar LA MordazaCortes EN General Corte DE Hueco Para UNA Caja DE Tomacorriente Figura HMontaje DEL Cortador Circular Figura Colocación DEL Cortador Circular Figura JUSO DEL Cortador Circular Figura K Detección DE Problemas Adaptador Para Aspiradoras Figura LNotas Especiales Paraeluso CON Baterías DE Litio MantenimientoGarantía Limitada DE Tres Años Piezas DE Repuesto Mantenimiento Y ReparacionesAccesorios Reemplazo DE LAS Etiquetas DE Advertencia EspecificacionespcmvcCatalog Number PC1800SS March

90562807, PC1800SS specifications

The Porter-Cable PC1800SS, 90562807 is a powerful cordless drill that has garnered attention for its impressive features and versatility. Designed for both professionals and DIY enthusiasts, this tool excels in various drilling and fastening tasks, making it a valuable addition to any toolkit.

At the heart of the PC1800SS is its robust 18-volt lithium-ion battery, which provides a reliable and consistent power source. This battery technology not only enhances runtime but also ensures shorter charging times, allowing users to complete projects more efficiently. With a fully charged battery, users can expect an extended duration of use, making it ideal for prolonged tasks or larger projects.

One of the standout features of the Porter-Cable PC1800SS is its two-speed gear mechanism, which offers speeds of 0-350 RPM and 0-1,500 RPM. This flexibility allows users to easily switch between high torque settings for heavier tasks and fast speeds for drilling into softer materials. Additionally, the drill provides a 1/2-inch keyless chuck that makes changing bits quick and easy, saving valuable time during operation.

The tool also incorporates an LED light that illuminates the workspace, making it easier to work in dimly lit environments. This feature is particularly helpful for tasks that require precision and detail. Coupled with its ergonomic design, the PC1800SS ensures maximum comfort during use, minimizing fatigue even during extended periods of operation.

With a built-in belt hook, the Porter-Cable PC1800SS offers convenience and accessibility, allowing users to keep the drill nearby without needing to set it down frequently. This feature is appreciated by professionals who move around job sites or those working in tight spaces.

In summary, the Porter-Cable PC1800SS, 90562807 is a versatile cordless drill that combines power, convenience, and advanced technology. Its lightweight design, impressive battery life, two-speed settings, and integrated LED light make it a go-to tool for a myriad of applications. Whether tackling home improvement projects or professional contracting tasks, this drill proves its worth with every use. With Porter-Cable’s commitment to quality and durability, the PC1800SS is a reliable choice that continues to meet the needs of users across various skill levels.
Top Page Image Contents