Porter-Cable 90562807, PC1800SS Problem Power Line, Leaving the Battery in the Charger

Page 9

90562807 PC1800SS rotary saw.qxd:??????-00 Cir Saw book 3/24/10 8:27 AM Page 9

PROBLEM POWER LINE

When the charger is used with some portable power sources such as generators or sources that convert DC to AC, the charger may temporarily suspend operation. The LED flashes in the pattern indicated on the label. This indicates that the power source is out of limits.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left connected with the LED glowing indefinitely. The charger will keep the battery pack fresh and fully charged. This charger features an automatic tune-up mode which equals or balances the individual cells in the battery pack to allow it to function at peak capacity. Battery packs should be tuned up weekly or whenever the battery no longer delivers the same amount of work. To use the automatic tune-up mode, place the battery pack in the charger and leave it for at least 8 hours.

IMPORTANT CHARGING NOTES

1.Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

2.The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

3.If the battery pack does not charge properly:

a.Check current at receptacle by plugging in a lamp or other appliance

b.Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

c.Move charger and battery pack to a location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C).

d.If charging problems persist, take the tool, battery pack and charger to your local service center.

4.The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack.

5.Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

6.Do not freeze or immerse charger in water or any other liquid.

: Shock hazard. Do not allow any liquid to get inside charger.Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling.

INSTALLING AND REMOVING THE BATTERY PACK FROM THE TOOL

NOTE: Make sure your battery pack is fully charged.

: Make sure the switch is in the off position before removing or installing battery.

•TO INSTALL BATTERY PACK: Insert battery pack into tool as shown in figure C.

C

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Catalog Number Advertencia Léase EsteGeneral Power Tool Safety Warnings Specific Safety Rules Page NI-CD Battery Packs and Chargers Description Cat. # LI-ION Battery Packs and Chargers Description Cat. #Important Safety Instructions for Battery Chargers Important Safety Instruction for Battery Packs Charging Procedure Battery CAP InformationCharger Diagnostics BAD BatteryLeaving the Battery in the Charger Problem Power LineInstalling and Removing the Battery Pack from the Tool Important Charging NotesInstalling and Removing the BIT Figures F, G ON/OFF Slider Switch Figure ETo Maintain Safe Tool Control Depth GuideChanging the Collet Never tighten the collet without a bit installedTo Change the Collet General CuttingCutting a Hole for AN Electrical Outlet Assembling Circle Cutter FigureAttaching Circle Cutter Figure J Using Circle Cutter Figure K TroubleshootingMaintenance Specialnotes for USE with Lithium BatteriesReplacement Parts Service and Repairs Three Year Limited WarrantyAccessories Rbrc SealHighway North Jackson, TN 888 DE Catalogue Page Page Consignes DE Sécurité Particulières Description De cat Lignes Directrices EN Matière DE Sécurité DéfinitionsSymboles Description FonctionnelleCalibre AWG Conserver CES Directives Lire Toutes LES Directives Directives DE Sécurité Importantes Pour LES BLOCS- PilesInformation Concernant LE Capuchon DU BLOC-PILE Piles au LI-ION dans les bagages enregistrésFonctions DE Diagnostic DU Chargeur Recommandations EN Matière DE RangementProcédure DE Charge Pile EN Mauvais ÉtatInsertion ET Retrait DU BLOC-PILES DE L’OUTIL Remarques Importantes Pour LE ChargementInterrupteur Coulissant MARCHE/ARRÊT Figure E Sécurité ET Maîtrise DE L’OUTILGuide DE Profondeur Pose ET Dépose DE LA Mèche Figures F, GRemplacement DE LA Douille Remplacement DE LA Douille DE SerrageNe jamais serrer la pince si aucune mèche n’est posée Coupes OrdinairesÉlectrique Figure H Monter LE Trépan FigureFixer LE Trépan Figure J Utiliser UN Trépan Figure K LE Sceau SrprcmcEntretien Pièces DE RechangeAccessoires Cause possible Solution possibleProblème DépannageGarantie Limitée DE Trois ANS Remplacement DES Étiquettes DʼAVERTISSEMENTCatálogo N Page Page Normas Específicas DE Seguridad Peligro Pautas DE SEGURIDAD/DEFINICIONESDescripción De cat Descripción DE LAS Funciones Figura aSímbolos Tamaño AWG del conductor Información Acerca DEL Protector DE LA Batería LEA Todas LAS InstruccionesProcedimiento DE Carga Recomendaciones CON Respecto AL AlmacenamientoDiagnóstico DEL Cargador Batería EN MAL EstadoLínea DE Potencia CON Problemas Dejar LA Batería EN EL CargadorNotas Importantes Sobre LA Carga Interruptor Deslizante DE ENCENDIDO/APAGADO Figura E Para Mantener UN Control Seguro Sobre HerramientaInstalación Y Extracción DE LA Broca Figuras F, G Guía DE ProfundidadCuando reemplace las brocas, no coloque el lado de las Ranuras dentro del collar. Esto puede romper la brocaPara Cambiar LA Mordaza Cambio DE MordazasCortes EN General Corte DE Hueco Para UNA Caja DE Tomacorriente Figura HMontaje DEL Cortador Circular Figura Colocación DEL Cortador Circular Figura JUSO DEL Cortador Circular Figura K Adaptador Para Aspiradoras Figura L Detección DE ProblemasNotas Especiales Paraeluso CON Baterías DE Litio MantenimientoGarantía Limitada DE Tres Años Piezas DE Repuesto Mantenimiento Y ReparacionesAccesorios Especificacionespcmvc Reemplazo DE LAS Etiquetas DE AdvertenciaCatalog Number PC1800SS March

90562807, PC1800SS specifications

The Porter-Cable PC1800SS, 90562807 is a powerful cordless drill that has garnered attention for its impressive features and versatility. Designed for both professionals and DIY enthusiasts, this tool excels in various drilling and fastening tasks, making it a valuable addition to any toolkit.

At the heart of the PC1800SS is its robust 18-volt lithium-ion battery, which provides a reliable and consistent power source. This battery technology not only enhances runtime but also ensures shorter charging times, allowing users to complete projects more efficiently. With a fully charged battery, users can expect an extended duration of use, making it ideal for prolonged tasks or larger projects.

One of the standout features of the Porter-Cable PC1800SS is its two-speed gear mechanism, which offers speeds of 0-350 RPM and 0-1,500 RPM. This flexibility allows users to easily switch between high torque settings for heavier tasks and fast speeds for drilling into softer materials. Additionally, the drill provides a 1/2-inch keyless chuck that makes changing bits quick and easy, saving valuable time during operation.

The tool also incorporates an LED light that illuminates the workspace, making it easier to work in dimly lit environments. This feature is particularly helpful for tasks that require precision and detail. Coupled with its ergonomic design, the PC1800SS ensures maximum comfort during use, minimizing fatigue even during extended periods of operation.

With a built-in belt hook, the Porter-Cable PC1800SS offers convenience and accessibility, allowing users to keep the drill nearby without needing to set it down frequently. This feature is appreciated by professionals who move around job sites or those working in tight spaces.

In summary, the Porter-Cable PC1800SS, 90562807 is a versatile cordless drill that combines power, convenience, and advanced technology. Its lightweight design, impressive battery life, two-speed settings, and integrated LED light make it a go-to tool for a myriad of applications. Whether tackling home improvement projects or professional contracting tasks, this drill proves its worth with every use. With Porter-Cable’s commitment to quality and durability, the PC1800SS is a reliable choice that continues to meet the needs of users across various skill levels.
Top Page Image Contents