Black & Decker 90504494 Using the Laser Level Function Horizontally Left Figure L, Screw Driving

Page 11

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 11

USING THE LASER LEVEL FUNCTION (HORIZONTALLY LEFT - FIGURE L)

•Place the tool flat against the wall as shown.

•Slide the laser on/off switch (6) to position I to switch the laser ON.

•Move the laser direction actuator (7 in Figure K) to the left most position. Laser will project horizontally to the left from the laser aperture (5 in Figure B).

•Move the tool as necessary to position the laser line.

NOTE: The laser lines will only be level if the tool is kept within 5 degrees from vertical.

•Slide the laser on/off switch (6) to position 0 to switch the laser OFF. NOTE: Laser will not work if the drill is inverted.

USING THE LASER LEVEL FUNCTION (VERTICALLY - FIGURE M)

•Place the tool flat against the wall as shown.

•Slide the laser on/off switch (6) to position I to switch the laser ON.

•Move the laser direction actuator (7 in Figure K) to the center position. Laser will project vertically from the laser aperture (5 in Figure B).

•Move the tool as necessary to position the laser line.

NOTE: The laser lines will only be level if the tool is kept within 5 degrees from vertical.

•Slide the laser on/off switch (6) to position 0 to switch the laser OFF. NOTE: Laser will not work if the drill is inverted.

USING THE LASER LEVEL FUNCTION (HORIZONTALLY RIGHT - FIGURE N)

•Place the tool flat against the wall as shown.

•Slide the laser on/off switch (6) to position I to switch the laser ON.

•Move the laser direction actuator (7 in Figure K) to the right most position. Laser will project horizontally to the right from the laser aperture (5 in Figure B).

•Move the tool as necessary to position the laser line.

NOTE: The laser lines will only be level if the tool is kept within 5 degrees from vertical.

•Slide the laser on/off switch (6) to position 0 to switch the laser OFF. NOTE: Laser will not work if the drill is inverted.

SCREW DRIVING

For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first.

ON BOARD BIT STORAGE

A bit storage slot is built-in to the area just above the battery pack.

DRILLING

•Use sharp drill bits only.

•Support and secure work properly, as instructed in the Safety Instructions.

•Use appropriate and required safety equipment, as instructed in the Safety Instructions.

•Secure and maintain work area, as instructed in the Safety Instructions.

•Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it.

•Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit.

•Hold the drill firmly with two hands to control its twisting action.

•DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT.

•Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole.

•Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.

•Make sure switch turns drill on and off.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents VEA EL Espa OL EN LA Contraportada Save this Manual for Future ReferenceGeneral Safety Rules Specific Safety Rules First Aid Measures for Gel Components Battery CAP InformationFunctional Description 90504494 02 BDGL1200 drill 8/29/06 839 AM BDGL1200 BDGL1440 Safety Instructions LasersCharging the Battery Pack BDGL1200 Figure C Safety Warnings and Instructions ChargingOperating Instructions Charging the Battery Pack BDGL1440, BDGL1800 Figure DSafety Warnings and Instructions Drills Trigger Switch & Reversing Button Figure FOperating the Laser Screw Driving Using the Laser Level Function Horizontally Left Figure LUsing the Laser Level Function Vertically Figure M Using the Laser Level Function Horizontally Right Figure NAccessories MaintenanceTechnical Specifications of Laser Service Information Full TWO-YEAR Home USE WarrantyConserver CE Manuel Pour UN Usage ULT Rieur Mode D EmploiGles de s curit g n rales Contrôler Premiers Soins Relatifs ¸ LA Composition DU GEL Règles DE Sécurité SpécifiquesInformation Concernant LE Capuchon DU BLOC-PILE Description Fonctionnelle90504494 02 BDGL1200 drill 8/29/06 839 AM 90504494 02 BDGL1200 drill 8/29/06 839 AM Directives DE S Curit Pour Lasers Chargement DU BLOC-PILES BDGL1200 Figure C Remarques Importantes DE Chargement Chargement DU BLOC-PILES BDGL1440, BDGL1800 Figure DFonctionnement Glage DE LA Direction DU Faisceau Laser Figure K Utilisation DU LaserMise EN Marche ET Hors Tension DU Laser Figure J Entretien VissageRangement INT GR DES Møches PER AGEDépannage AccessoiresCaract Ristiques Techniques DU Laser Conserve Este Manual Para Futuras Consultas Meros DE CAT LogoNormas generales de seguridad 90504494 02 BDGL1200 drill 8/29/06 839 AM Normas DE Seguridad Específicas Informaci N Acerca DEL Protector DE LA Baterœa Descripci N DE LAS Funciones90504494 02 BDGL1200 drill 8/29/06 839 AM Instrucciones DE Seguridad Para EL L SER Advertencias E Instrucciones DE Seguridad Cargar Carga DEL Paquete DE Baterœas BDGL1440, BDGL1800 Figura D Carga DEL Paquete DE Baterœas BDGL1200 Figura CInterruptor Disparador Y BOT N DE Inversi N Figura F Notas Importantes Sobre LA CargaInstrucciones Y Advertencias DE Seguridad Taladros Encendido Y Apagado DEL L SER Figura J Engranaje DE Doble Alcance Figura G BDGL1800 SolamenteControl DE Torsi N Figura H Portabrocas SIN Llave FiguraEspacio EN LA Herramienta Para Guardar Brocas Configuraci N DE LA Direcci N DEL Rayo Figura KDestornillado Mantenimiento Detección DE ProblemasTaladrado Accesorios MEXICO, D.F CULIACAN, SIN MONTERREY, N.LGUADALAJARA, JAL PUEBLA, PUE90504494 02 BDGL1200 drill 8/29/06 839 AM
Top Page Image Contents