Western Telematic CMS-16 manual Network Parameters Menu Supervisor Mode Only

Page 28

WTI CMS-16; Console Management Switch -- User's Guide

Figure 5.3: Network Parameters Menu (Supervisor Mode Only)

To access the Network Parameters menu, type /N and press [Enter]. The screen shown in Figure 5.3 will be displayed. Note that the Network Parameters menu is only available in Supervisor Mode. The Network Parameters menu offers the following options:

1.IP Address: Defines the IP Address for the CMS unit. Type 1 press [Enter], and follow the instructions in the submenu. (Default = undefined).

2.Subnet Mask: Defines the Subnet Mask for the CMS unit. Type 2 press [Enter], and follow the instructions in the submenu. (Default = undefined).

3.Gateway Address: Defines the Gateway Address for the CMS unit. Type 3 press [Enter], and follow the instructions in the submenu. (Default = undefined).

4.IP Security: Sets up the IP Security feature as described in Section 5.5.5.

11.Port Name: (Up to 16 characters) Assigns a name to the Network Port. (Default = undefined).

12.Supervisor Mode: Permits or denies access to the Supervisor Mode. When enabled (Permit), and the valid Supervisor Password is entered, this port may then issue Supervisor level commands. If disabled (Deny), the port may not enter Supervisor Mode, even when the Supervisor Password is entered. (Default = Permit).

13.Logoff Character: Defines the Logoff Character for the Network Port. The Logoff Character determines the disconnect sequence that is issued at this port in order to disconnect from a second port (Resident Disconnect). When defining the Logofff Character, note the following:

●The default Logoff Character is "+". As a result, the default Resident Disconnect Sequence is [Enter]+++[Enter].

●The default three character Resident Disconnect Sequence uses the format [Enter]LLL[Enter], where L is the Logoff Character. If the one character disconnect is selected (see item 14), a resident connection is terminated by simply typing the Logoff Character once (without carriage returns)

14.Sequence Disconnect: Enables/Disables and configures the Resident Disconnect command. This prompt offers the option to either disable the Sequence Disconnect, select a three character format, or a one character format. (Default = Three Characters). Note the following:

●When a Resident Connection is initiated, the CMS will send a message which lists connected ports, and displays the one character or three character disconnect

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (28 of 59) [11/15/2000 10:52:03 AM]

Page 27 Page 29
Image 28
Page 27 Page 29
Contents CMS-16 Battery Replacement Nameplate Power WarningRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide Appendices List of FiguresIntroduction Typographic ConventionsFront Panel Unit DescriptionBold Font Getting Started Power Cable Receptacle Power SwitchBack Panel Apply Power to the CMS System SetUp PortsUsing Other Parameters for this Overview Optional Communication ParametersConnecting your PC to the CMS Communicating with the CMS UnitDisplay Free Any Undefined Enter /H for Command Menu Hardware Installation Connecting Power to the CMS UnitAC Powered Units DC Powered UnitsConfigure Option Switches Default Baud Rate Sw1, Sw2, Sw3Default Response Message Format Sw6 Default Handshake Sw4, Sw5Default Command Echo Sw7 Connecting Devices to the CMS Initialize Unit to Default SettingsApplication Example CMS Application Example Not to Scale Configuration Access to the CMS Command ModePassword Functions $ telnet 192.1.1.1 EnterSupervisor Password Port PasswordsDefining the Site ID and Supervisor Password Port Configuration Configuration Conventions3. RS232 Port Configuration Menus Port ModesStop Bits Default = CTS/RTSAT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Network Port Configuration Menu Telnet Port ParametersNetwork Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Save User Selected Parameters Status ScreensPort Status Screen /S Port Diagnostics Screen /SD Port Status Screen Supervisor Mode, Defaults ShownPort Name Status Baud COM HS Mode BUF CTS Network Status Screen /SN Port Parameters Screens /WWP xx Enter Operation Any-to-Any ModePort Connection and Disconnection Disconnecting Ports Enter Defining Hunt Groups Hunt Group ExamplePassive Mode Buffer ModeXx Enter Reading Data from Buffer Mode PortsPort Buffers Saving and Restoring Configuration Parameters Modem ModeSending Parameters to a File Restoring Saved ParametersUpgrading CMS Firmware Command Reference Guide Command ConventionsCommand Response Terse VerboseCommand Summary Command Availability Supervisor UserCommand Set Enter Enter Command ModeEnter+++Enter Resident Disconnect Sequence ConnectThird Party Disconnect CP Copy RS232 Port ParametersErase Buffer Set System Parameters Default and TestHelp Set Network Port Parameters Display Site IDSet RS232 Port Parameters SD Display Port Diagnostics Reset Network PortDisplay Port Status SN Display Network StatusSave Parameters UF Upgrade FirmwareDisplay Port Parameters Who Appendix A. RS232 Port Interface Exit Command ModeFormat /X Enter Appendix B. Specifications Appendix C. Customer ServicePower Stop Bits 1 orTrademark and Copyright Information Trademarks Used in this Manual
Related manuals
Manual 62 pages 40.13 Kb
Top Page Image Contents