Western Telematic CMS-16 manual Hardware Installation, Connecting Power to the CMS Unit

Page 13

WTI CMS-16; Console Management Switch -- User's Guide

and press [Enter].

b.To display the Site I.D., type /J [Enter].

c.Note that the Site I.D. will be cleared when the unit is initialized.

This completes the introductory overview of the CMS. Please proceed to Section 4 and Section 5 for complete installation and configuration procedures.

4. Hardware Installation

4.1. Connecting Power to the CMS Unit

The CMS is available in both AC and DC powered versions. When connecting AC or DC power to the CMS, proceed as follows:

CAUTION: This device should only be operated with the type of power source indicated on the instrument nameplate. If you are not sure of the type of power service available, please consult your local power company.

4.1.1. AC Powered Units

Plug the supplied power cable into the receptacle on the CMS back panel and then connect the power cable to a grounded AC outlet. The AC powered version of the CMS features a self adjusting power supply that automatically adapts to power supplies between 90 and 250 VAC.

4.1.2. DC Powered Units

The DC terminal block features two bus inputs as shown in Figure 4.1 below. This allows the user to connect only one DC power source, or connect two DC power sources where the second source functions as a backup.

When connecting the CMS to your DC power source, first remove the clear protective cover from the DC terminal block, attach the wires from the -48V DC power source to the screw terminals, connect your ground line to the labeled ground screw, and then replace the protective cover.

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (13 of 59) [11/15/2000 10:52:02 AM]

Image 13

Contents CMS-16 Battery Replacement Nameplate Power WarningRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide List of Figures AppendicesTypographic Conventions IntroductionFront Panel Unit DescriptionBold Font Getting Started Power Cable Receptacle Power SwitchBack Panel System SetUp Ports Apply Power to the CMSUsing Other Parameters for this Overview Optional Communication ParametersCommunicating with the CMS Unit Connecting your PC to the CMSDisplay Free Any Undefined Enter /H for Command Menu Connecting Power to the CMS Unit Hardware InstallationAC Powered Units DC Powered UnitsDefault Baud Rate Sw1, Sw2, Sw3 Configure Option SwitchesDefault Response Message Format Sw6 Default Handshake Sw4, Sw5Default Command Echo Sw7 Connecting Devices to the CMS Initialize Unit to Default SettingsApplication Example CMS Application Example Not to Scale Access to the CMS Command Mode Configuration$ telnet 192.1.1.1 Enter Password FunctionsPort Passwords Supervisor PasswordDefining the Site ID and Supervisor Password Configuration Conventions Port ConfigurationPort Modes 3. RS232 Port Configuration MenusCTS/RTS Stop Bits Default =AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Telnet Port Parameters Network Port Configuration MenuNetwork Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Save User Selected Parameters Status ScreensPort Status Screen /S Port Status Screen Supervisor Mode, Defaults Shown Port Diagnostics Screen /SDPort Name Status Baud COM HS Mode BUF CTS Port Parameters Screens /W Network Status Screen /SNWP xx Enter Operation Any-to-Any ModePort Connection and Disconnection Disconnecting Ports Enter Hunt Group Example Defining Hunt GroupsBuffer Mode Passive ModeXx Enter Reading Data from Buffer Mode PortsPort Buffers Modem Mode Saving and Restoring Configuration ParametersRestoring Saved Parameters Sending Parameters to a FileUpgrading CMS Firmware Command Conventions Command Reference GuideTerse Verbose Command ResponseCommand Availability Supervisor User Command SummaryEnter Enter Command Mode Command SetConnect Enter+++Enter Resident Disconnect SequenceThird Party Disconnect CP Copy RS232 Port ParametersErase Buffer Set System Parameters Default and TestHelp Set Network Port Parameters Display Site IDSet RS232 Port Parameters Reset Network Port SD Display Port DiagnosticsDisplay Port Status SN Display Network StatusSave Parameters UF Upgrade FirmwareDisplay Port Parameters Who Appendix A. RS232 Port Interface Exit Command ModeFormat /X Enter Appendix C. Customer Service Appendix B. SpecificationsPower Stop Bits 1 orTrademarks Used in this Manual Trademark and Copyright Information

Related manuals

Manual 62 pages 40.13 Kb