Western Telematic CMS-16 manual Copy Port Parameters Menu

Page 32

WTI CMS-16; Console Management Switch -- User's Guide

1.Access the CMS command mode. If the password prompt is displayed, key in your Supervisor Level Password.

2.At the command prompt, type /CP and press [Enter], the menu shown in Figure 5.5 will be displayed.

1.	Port Name:	(undefined)
2.	Password:	(undefined)
3.	Baud Rate:
4.	Bits/Parity:
5.	Stop Bits:
6.	Handshake Mode:
7.	Port Mode:
8.	74. DTR Output:
8.	Supervisor Mode:
9.	Logoff Character:
10.	Sequence Disconnect:
11.	Timeout Disconnect:
12.	Response Type:
13.	Command Echo:
14.	Accept Break:

(Note: Ports 1 & 2 will NOT have restricted values changed.)

Enter: Parameter # <CR> to define parameter value to copy to all ports, -<CR> to remove all values set,

X<CR> to exit WITHOUT copy,

<ESC> to copy to all ports and exit ...

Figure 5.5: The Copy Port Parameters Menu

3.Selecting Parameters: To select parameters to be copied, key in the number for the desired parameter, press [Enter], and then follow the instructions in the submenu. Note that it is not necessary to define all port parameters, for example, the /CP command could be used to select only the Baud Rate for all ports.

Note: The /CP command will only copy the parameters that are currently displayed by the Copy Port Parameters menu. Note that although the Port Password is not displayed, the selected password will be copied if the field for this item reads "defined".

4.Clear Menu: After defining several parameters, if you wish to clear the /CP menu and start again, type - (dash) and press [Enter], the menu will be reset.

5.Copy Parameters: When you have finished selecting parameters, press [Esc] to copy the selected parameters to all CMS RS-232 Ports and exit from the Copy Port Parameters menu.

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (32 of 59) [11/15/2000 10:52:03 AM]

Image 32

Contents CMS-16 Rack Mount Installation Nameplate Power WarningBattery Replacement Table of Contents WTI CMS-16 Console Management Switch -- Users Guide Appendices List of FiguresIntroduction Typographic ConventionsBold Font Unit DescriptionFront Panel Back Panel Power Cable Receptacle Power SwitchGetting Started Apply Power to the CMS System SetUp PortsUsing Other Parameters for this Overview Optional Communication ParametersConnecting your PC to the CMS Communicating with the CMS UnitDisplay Free Any Undefined Enter /H for Command Menu Hardware Installation Connecting Power to the CMS UnitAC Powered Units DC Powered UnitsConfigure Option Switches Default Baud Rate Sw1, Sw2, Sw3Default Command Echo Sw7 Default Handshake Sw4, Sw5Default Response Message Format Sw6 Application Example Initialize Unit to Default SettingsConnecting Devices to the CMS CMS Application Example Not to Scale Configuration Access to the CMS Command ModePassword Functions $ telnet 192.1.1.1 EnterSupervisor Password Port PasswordsDefining the Site ID and Supervisor Password Port Configuration Configuration Conventions3. RS232 Port Configuration Menus Port ModesStop Bits Default = CTS/RTSAT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Network Port Configuration Menu Telnet Port ParametersNetwork Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Port Status Screen /S Status ScreensSave User Selected Parameters Port Diagnostics Screen /SD Port Status Screen Supervisor Mode, Defaults ShownPort Name Status Baud COM HS Mode BUF CTS Network Status Screen /SN Port Parameters Screens /WWP xx Enter Port Connection and Disconnection Any-to-Any ModeOperation Disconnecting Ports Enter Defining Hunt Groups Hunt Group ExamplePassive Mode Buffer ModePort Buffers Reading Data from Buffer Mode PortsXx Enter Saving and Restoring Configuration Parameters Modem ModeSending Parameters to a File Restoring Saved ParametersUpgrading CMS Firmware Command Reference Guide Command ConventionsCommand Response Terse VerboseCommand Summary Command Availability Supervisor UserCommand Set Enter Enter Command ModeEnter+++Enter Resident Disconnect Sequence ConnectErase Buffer CP Copy RS232 Port ParametersThird Party Disconnect Help Default and TestSet System Parameters Set RS232 Port Parameters Display Site IDSet Network Port Parameters SD Display Port Diagnostics Reset Network PortDisplay Port Status SN Display Network StatusDisplay Port Parameters Who UF Upgrade FirmwareSave Parameters Format /X Enter Exit Command ModeAppendix A. RS232 Port Interface Appendix B. Specifications Appendix C. Customer ServicePower Stop Bits 1 orTrademark and Copyright Information Trademarks Used in this Manual

Related manuals

Manual 62 pages 40.13 Kb