Western Telematic CMS-16 manual Table of Contents

Page 3

WTI CMS-16; Console Management Switch -- User's Guide

2.Open Racks: Make certain that the rack frame does not block the ventilation slots on the instrument cover. If the device is installed on sliders, check the unit when seated all the way into the rack to make certain that ventilation slots are not blocked.

Ventilation

Slots in the instrument cover are provided to allow ventilation for heat dissipation. To ensure safe, reliable operation, these openings must not be covered or blocked.

Disconnect Power

If any of the following events are noted, immediately disconnect the unit from the outlet and contact qualified service personnel:

●If the power cord becomes frayed or damaged.

●If liquid has been spilled into the device or if the device has been exposed to rain or water.

Table of Contents

●1. Introduction

●2. Unit Description

❍2.1. Front Panel

❍2.2. Back Panel

●3. Getting Started

❍3.1. Communication Parameters

❍3.2. Apply Power to the CMS

❍3.3. System SetUp Ports

❍3.4. Connecting your PC to the CMS

❍3.5. Communicating with the CMS Unit

●4. Hardware Installation

❍4.1. Connecting Power to the CMS Unit

■4.1.1. AC Powered Units

■4.1.2. DC Powered Units

❍4.2. Configure Option Switches

■4.2.1. Default Baud Rate (Sw1, Sw2, Sw3)

■4.2.2. Default Handshake (Sw4, Sw5)

■4.2.3. Default Response Message Format (Sw6)

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (3 of 59) [11/15/2000 10:52:02 AM]

Image 3

Contents CMS-16 Nameplate Power Warning Battery ReplacementRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide List of Figures AppendicesTypographic Conventions IntroductionUnit Description Front PanelBold Font Power Cable Receptacle Power Switch Getting StartedBack Panel Communication Parameters Apply Power to the CMSSystem SetUp Ports Using Other Parameters for this Overview OptionalCommunicating with the CMS Unit Connecting your PC to the CMSDisplay Free Any Undefined Enter /H for Command Menu DC Powered Units Hardware InstallationConnecting Power to the CMS Unit AC Powered UnitsDefault Baud Rate Sw1, Sw2, Sw3 Configure Option SwitchesDefault Handshake Sw4, Sw5 Default Response Message Format Sw6Default Command Echo Sw7 Initialize Unit to Default Settings Connecting Devices to the CMSApplication Example CMS Application Example Not to Scale Access to the CMS Command Mode Configuration$ telnet 192.1.1.1 Enter Password FunctionsPort Passwords Supervisor PasswordDefining the Site ID and Supervisor Password Configuration Conventions Port ConfigurationPort Modes 3. RS232 Port Configuration MenusCTS/RTS Stop Bits Default =AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Telnet Port Parameters Network Port Configuration MenuNetwork Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Status Screens Save User Selected ParametersPort Status Screen /S Port Status Screen Supervisor Mode, Defaults Shown Port Diagnostics Screen /SDPort Name Status Baud COM HS Mode BUF CTS Port Parameters Screens /W Network Status Screen /SNWP xx Enter Any-to-Any Mode OperationPort Connection and Disconnection Disconnecting Ports Enter Hunt Group Example Defining Hunt GroupsBuffer Mode Passive ModeReading Data from Buffer Mode Ports Xx EnterPort Buffers Modem Mode Saving and Restoring Configuration ParametersRestoring Saved Parameters Sending Parameters to a FileUpgrading CMS Firmware Command Conventions Command Reference GuideTerse Verbose Command ResponseCommand Availability Supervisor User Command SummaryEnter Enter Command Mode Command SetConnect Enter+++Enter Resident Disconnect SequenceCP Copy RS232 Port Parameters Third Party DisconnectErase Buffer Default and Test Set System ParametersHelp Display Site ID Set Network Port ParametersSet RS232 Port Parameters SN Display Network Status SD Display Port DiagnosticsReset Network Port Display Port StatusUF Upgrade Firmware Save ParametersDisplay Port Parameters Who Exit Command Mode Appendix A. RS232 Port InterfaceFormat /X Enter Stop Bits 1 or Appendix B. SpecificationsAppendix C. Customer Service PowerTrademarks Used in this Manual Trademark and Copyright Information

Related manuals

Manual 62 pages 40.13 Kb