Western Telematic CMS-16 manual Set System Parameters, Help, Default and Test

Page 53

WTI CMS-16; Console Management Switch -- User's Guide

recovered.

Availability: Supervisor Only

Format: /E[/Y] <x> [x] [Enter]

Where:

xIs the number or name of the port buffer(s) to be cleared. To erase buffers for all ports, enter an asterisk.

/Y (Optional) Suppresses the "SURE? (Y/N)" prompt.

Response:

Verbose: "Are You Sure (y/n)?", if Y, the unit will respond with "OK".

Terse: 5, if Y, the unit will respond with 0.

Example: To clear the buffer for Port 3, access the Command Mode from a port with "All" command capability, and type /E 3 [Enter].

/F Set System Parameters

Displays a menu which is used to define the Site ID message and Supervisor Password. When the Supervisor Password is defined, the CMS will display a password prompt before allowing access to command mode. For more information, refer to Section 5.4.

Note: Make certain to record your Supervisor Password for future reference. If the Supervisor Password is lost or forgotten, you will not be able to access Supervisor Level commands.

Availability: Supervisor Only

Format: /F [Enter]

Response: Displays System Parameters Menu

/H Help

Displays a Help Screen, which lists all CMS commands along with a brief description of each command.

Availability: Supervisor / User

Format: /H [Enter]

Response: Displays Help Screen. Note that the User Level Help Screen does not include Supervisor Level Commands.

/I Default and Test

Tests internal memory and initializes the unit with the default parameters specified by the Option

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (53 of 59) [11/15/2000 10:52:03 AM]

Image 53
Contents CMS-16 Rack Mount Installation Nameplate Power WarningBattery Replacement Table of Contents WTI CMS-16 Console Management Switch -- Users Guide List of Figures AppendicesTypographic Conventions IntroductionBold Font Unit DescriptionFront Panel Back Panel Power Cable Receptacle Power SwitchGetting Started System SetUp Ports Apply Power to the CMSUsing Other Parameters for this Overview Optional Communication ParametersCommunicating with the CMS Unit Connecting your PC to the CMSDisplay Free Any Undefined Enter /H for Command Menu Connecting Power to the CMS Unit Hardware InstallationAC Powered Units DC Powered UnitsDefault Baud Rate Sw1, Sw2, Sw3 Configure Option SwitchesDefault Command Echo Sw7 Default Handshake Sw4, Sw5Default Response Message Format Sw6 Application Example Initialize Unit to Default SettingsConnecting Devices to the CMS CMS Application Example Not to Scale Access to the CMS Command Mode Configuration$ telnet 192.1.1.1 Enter Password FunctionsPort Passwords Supervisor PasswordDefining the Site ID and Supervisor Password Configuration Conventions Port ConfigurationPort Modes 3. RS232 Port Configuration MenusCTS/RTS Stop Bits Default =AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Telnet Port Parameters Network Port Configuration MenuNetwork Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Port Status Screen /S Status ScreensSave User Selected Parameters Port Status Screen Supervisor Mode, Defaults Shown Port Diagnostics Screen /SDPort Name Status Baud COM HS Mode BUF CTS Port Parameters Screens /W Network Status Screen /SNWP xx Enter Port Connection and Disconnection Any-to-Any ModeOperation Disconnecting Ports Enter Hunt Group Example Defining Hunt GroupsBuffer Mode Passive ModePort Buffers Reading Data from Buffer Mode PortsXx Enter Modem Mode Saving and Restoring Configuration ParametersRestoring Saved Parameters Sending Parameters to a FileUpgrading CMS Firmware Command Conventions Command Reference GuideTerse Verbose Command ResponseCommand Availability Supervisor User Command SummaryEnter Enter Command Mode Command SetConnect Enter+++Enter Resident Disconnect SequenceErase Buffer CP Copy RS232 Port ParametersThird Party Disconnect Help Default and TestSet System Parameters Set RS232 Port Parameters Display Site IDSet Network Port Parameters Reset Network Port SD Display Port DiagnosticsDisplay Port Status SN Display Network StatusDisplay Port Parameters Who UF Upgrade FirmwareSave Parameters Format /X Enter Exit Command ModeAppendix A. RS232 Port Interface Appendix C. Customer Service Appendix B. SpecificationsPower Stop Bits 1 orTrademarks Used in this Manual Trademark and Copyright Information
Related manuals
Manual 62 pages 40.13 Kb