Western Telematic CMS-16 manual Command Set, Enter Enter Command Mode

Page 50

WTI CMS-16; Console Management Switch -- User's Guide
Erase Buffer	/E[/Y] <x> [x] [Enter]		X
	/E[/Y] *	[Enter]
Reset Network Port	/T [Enter]		X
Default & Test	/I[/Y] [Enter]		X
Save Parameters	/U [Enter]		X
Upgrade Firmware	/UF [Enter]		X

(1)Supervisor Mode displays parameters for all ports;

User Mode only displays parameters for the ports allowed by the Port Password.

(2)To display Port Passwords, include the "P" Option. (Supervisor Only).

(3)A port with "User" command capability can only view its own parameters. A User Port cannot view parameters for other ports.

(4)A User Port cannot perform a Third Party Connect.

(5)Resident Disconnect: Disconnects your resident port from another port. Note that the Resident Disconnect Sequence can be redefined via the Port Configuration Menus.

(6)Third Party Disconnect: Disconnects two or more nonresident ports. Must be issued from a third port with Supervisor command capability.

10.4.Command Set

This Section provides more detailed information on all CMS commands, sorted alphabetically by name.

[Enter] Enter Command Mode

In order to set parameters or connect ports, you must first access the command mode as described in Section 5.1. When the Command Mode is inactive (port asleep), the port will only respond when the [Enter] key is pressed without any characters preceding it. If the Supervisor Password (command /F) has been defined, the unit will require a password before allowing access to Command Mode.

Availability: Supervisor / User

Format: [Enter] (Press [Enter] twice if other characters have already been typed).

Response: The Port Status Screen will be displayed, followed by the "CMS>" command prompt.

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (50 of 59) [11/15/2000 10:52:03 AM]

Image 50

Contents CMS-16 Rack Mount Installation Nameplate Power WarningBattery Replacement Table of Contents WTI CMS-16 Console Management Switch -- Users Guide Appendices List of FiguresIntroduction Typographic ConventionsBold Font Unit DescriptionFront Panel Back Panel Power Cable Receptacle Power SwitchGetting Started Using Other Parameters for this Overview Optional Apply Power to the CMSSystem SetUp Ports Communication ParametersConnecting your PC to the CMS Communicating with the CMS UnitDisplay Free Any Undefined Enter /H for Command Menu AC Powered Units Hardware InstallationConnecting Power to the CMS Unit DC Powered UnitsConfigure Option Switches Default Baud Rate Sw1, Sw2, Sw3Default Command Echo Sw7 Default Handshake Sw4, Sw5Default Response Message Format Sw6 Application Example Initialize Unit to Default SettingsConnecting Devices to the CMS CMS Application Example Not to Scale Configuration Access to the CMS Command ModePassword Functions $ telnet 192.1.1.1 EnterSupervisor Password Port PasswordsDefining the Site ID and Supervisor Password Port Configuration Configuration Conventions3. RS232 Port Configuration Menus Port ModesStop Bits Default = CTS/RTSAT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Network Port Configuration Menu Telnet Port ParametersNetwork Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Port Status Screen /S Status ScreensSave User Selected Parameters Port Diagnostics Screen /SD Port Status Screen Supervisor Mode, Defaults ShownPort Name Status Baud COM HS Mode BUF CTS Network Status Screen /SN Port Parameters Screens /WWP xx Enter Port Connection and Disconnection Any-to-Any ModeOperation Disconnecting Ports Enter Defining Hunt Groups Hunt Group ExamplePassive Mode Buffer ModePort Buffers Reading Data from Buffer Mode PortsXx Enter Saving and Restoring Configuration Parameters Modem ModeSending Parameters to a File Restoring Saved ParametersUpgrading CMS Firmware Command Reference Guide Command ConventionsCommand Response Terse VerboseCommand Summary Command Availability Supervisor UserCommand Set Enter Enter Command ModeEnter+++Enter Resident Disconnect Sequence ConnectErase Buffer CP Copy RS232 Port ParametersThird Party Disconnect Help Default and TestSet System Parameters Set RS232 Port Parameters Display Site IDSet Network Port Parameters Display Port Status SD Display Port DiagnosticsReset Network Port SN Display Network StatusDisplay Port Parameters Who UF Upgrade FirmwareSave Parameters Format /X Enter Exit Command ModeAppendix A. RS232 Port Interface Power Appendix B. SpecificationsAppendix C. Customer Service Stop Bits 1 orTrademark and Copyright Information Trademarks Used in this Manual

Related manuals

Manual 62 pages 40.13 Kb