Western Telematic CMS-16 manual Stop Bits Default =, Cts/Rts

Page 24

WTI CMS-16; Console Management Switch -- User's Guide

. If the /P Command is entered without the port number (e.g. /P [Enter]), the configuration menu for your resident port will be displayed.

b. The /P command is only available in the Supervisor Mode

1.	Port Name:	(undefined)
2.	Password:	(undefined)
3.	Baud Rate:	9600
4.	Bits/Parity:	8-None
5.	Stop Bits:	1
6.	Handshake Mode:	CTS/RTS
7.	Port Mode:	Any-to-Any
8.	74. DTR Output:	Pulse
8.	Supervisor Mode:	Permit
9.	Logoff Character:	+
10.	Sequence Disconnect:	Three Characters
11.	Timeout Disconnect:	Off
12.	Response Type:	Verbose
13.	Command Echo:	On
14.	Accept Break:	Yes

Enter: "<" Previous Port,

">" Next Port,

<ESC> Exit ...

Figure 5.1: Port Configuration Menu (Port 2 Shown)

The Port Configuration menu offers the following options:

●1. Port Name: (Up to 16 characters) Assigns a name to the port. (Default = undefined).

●2. Password: (Up to 16 characters) Defines the Port Password for this port. Note that identical Port Passwords are generally assigned to several ports. When this password is entered at the login prompt, the user will then have access to all ports that share this password. (Default = undefined).

Note: The Port Password is not displayed by the Port Parameters menu. When the Port Password has been defined, the field for this item will read "defined". To display Port Passwords, invoke the /SP or /WP commands as described in Section 6.

●3. Baud Rate: Selects the baud rate for the port. Can be set to any standard rate from 300 bps to 115.2K bps. (Default = Selected By Option Switches 1, 2, and 3)

●4. Bits/Parity: (Default = 8-None).

●5. Stop Bits: (Default = 1).

●6. Handshake Mode: Selects the handshake format for this port; XON/XOFF, RTS/CTS (hardware), Both, or None. (Default = RTS/CTS).

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (24 of 59) [11/15/2000 10:52:02 AM]

Image 24

Contents CMS-16 Nameplate Power Warning Battery ReplacementRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide Appendices List of FiguresIntroduction Typographic ConventionsUnit Description Front PanelBold Font Power Cable Receptacle Power Switch Getting StartedBack Panel Apply Power to the CMS System SetUp PortsUsing Other Parameters for this Overview Optional Communication ParametersConnecting your PC to the CMS Communicating with the CMS UnitDisplay Free Any Undefined Enter /H for Command Menu Hardware Installation Connecting Power to the CMS UnitAC Powered Units DC Powered UnitsConfigure Option Switches Default Baud Rate Sw1, Sw2, Sw3Default Handshake Sw4, Sw5 Default Response Message Format Sw6Default Command Echo Sw7 Initialize Unit to Default Settings Connecting Devices to the CMSApplication Example CMS Application Example Not to Scale Configuration Access to the CMS Command ModePassword Functions $ telnet 192.1.1.1 EnterSupervisor Password Port PasswordsDefining the Site ID and Supervisor Password Port Configuration Configuration Conventions3. RS232 Port Configuration Menus Port ModesStop Bits Default = CTS/RTSAT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Network Port Configuration Menu Telnet Port ParametersNetwork Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Status Screens Save User Selected ParametersPort Status Screen /S Port Diagnostics Screen /SD Port Status Screen Supervisor Mode, Defaults ShownPort Name Status Baud COM HS Mode BUF CTS Network Status Screen /SN Port Parameters Screens /WWP xx Enter Any-to-Any Mode OperationPort Connection and Disconnection Disconnecting Ports Enter Defining Hunt Groups Hunt Group ExamplePassive Mode Buffer ModeReading Data from Buffer Mode Ports Xx EnterPort Buffers Saving and Restoring Configuration Parameters Modem ModeSending Parameters to a File Restoring Saved ParametersUpgrading CMS Firmware Command Reference Guide Command ConventionsCommand Response Terse VerboseCommand Summary Command Availability Supervisor UserCommand Set Enter Enter Command ModeEnter+++Enter Resident Disconnect Sequence ConnectCP Copy RS232 Port Parameters Third Party DisconnectErase Buffer Default and Test Set System ParametersHelp Display Site ID Set Network Port ParametersSet RS232 Port Parameters SD Display Port Diagnostics Reset Network PortDisplay Port Status SN Display Network StatusUF Upgrade Firmware Save ParametersDisplay Port Parameters Who Exit Command Mode Appendix A. RS232 Port InterfaceFormat /X Enter Appendix B. Specifications Appendix C. Customer ServicePower Stop Bits 1 orTrademark and Copyright Information Trademarks Used in this Manual

Related manuals

Manual 62 pages 40.13 Kb