Western Telematic CMS-16 Appendix A. RS232 Port Interface, Exit Command Mode, Format /X Enter

Page 57

WTI CMS-16; Console Management Switch -- User's Guide

Response: Displays port parameters.

Example: To display parameters for a port named "SERVER", access the Command Mode from a port with Supervisor Level command capability, and type /W SERVER [Enter].

/X Exit Command Mode

Exits Command Mode, When issued at the Net Port, also ends the telnet session. Note that exiting from Command Mode will not terminate port connections.

●Any-to-Any Mode: Exits Command Mode.

●Modem Mode: Disconnects and resets modem, hang-up message is sent, hardware line to modem drops for 500 ms, and reset message is sent.

Availability: Supervisor / User

Format: /X [Enter]

Response: Disconnected

Appendix A. RS232 Port Interface

Figure A.1: RS232 Port Interface

DCD and DTR hardware lines function as follows:

1. When connected:

. If either port is set for Modem Mode, the DTR output at either port reflects the DCD input at the other end.

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (57 of 59) [11/15/2000 10:52:03 AM]

Image 57

Contents CMS-16 Nameplate Power Warning Battery ReplacementRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide List of Figures AppendicesTypographic Conventions IntroductionUnit Description Front PanelBold Font Power Cable Receptacle Power Switch Getting StartedBack Panel System SetUp Ports Apply Power to the CMSUsing Other Parameters for this Overview Optional Communication ParametersCommunicating with the CMS Unit Connecting your PC to the CMSDisplay Free Any Undefined Enter /H for Command Menu Connecting Power to the CMS Unit Hardware InstallationAC Powered Units DC Powered UnitsDefault Baud Rate Sw1, Sw2, Sw3 Configure Option SwitchesDefault Handshake Sw4, Sw5 Default Response Message Format Sw6Default Command Echo Sw7 Initialize Unit to Default Settings Connecting Devices to the CMSApplication Example CMS Application Example Not to Scale Access to the CMS Command Mode Configuration$ telnet 192.1.1.1 Enter Password FunctionsPort Passwords Supervisor PasswordDefining the Site ID and Supervisor Password Configuration Conventions Port ConfigurationPort Modes 3. RS232 Port Configuration MenusCTS/RTS Stop Bits Default =AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Telnet Port Parameters Network Port Configuration MenuNetwork Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Status Screens Save User Selected ParametersPort Status Screen /S Port Status Screen Supervisor Mode, Defaults Shown Port Diagnostics Screen /SDPort Name Status Baud COM HS Mode BUF CTS Port Parameters Screens /W Network Status Screen /SNWP xx Enter Any-to-Any Mode OperationPort Connection and Disconnection Disconnecting Ports Enter Hunt Group Example Defining Hunt GroupsBuffer Mode Passive ModeReading Data from Buffer Mode Ports Xx EnterPort Buffers Modem Mode Saving and Restoring Configuration ParametersRestoring Saved Parameters Sending Parameters to a FileUpgrading CMS Firmware Command Conventions Command Reference GuideTerse Verbose Command ResponseCommand Availability Supervisor User Command SummaryEnter Enter Command Mode Command SetConnect Enter+++Enter Resident Disconnect SequenceCP Copy RS232 Port Parameters Third Party DisconnectErase Buffer Default and Test Set System ParametersHelp Display Site ID Set Network Port ParametersSet RS232 Port Parameters Reset Network Port SD Display Port DiagnosticsDisplay Port Status SN Display Network StatusUF Upgrade Firmware Save ParametersDisplay Port Parameters Who Exit Command Mode Appendix A. RS232 Port InterfaceFormat /X Enter Appendix C. Customer Service Appendix B. SpecificationsPower Stop Bits 1 orTrademarks Used in this Manual Trademark and Copyright Information

Related manuals

Manual 62 pages 40.13 Kb