Western Telematic CMS-16 manual Appendices, List of Figures

Page 5

WTI CMS-16; Console Management Switch -- User's Guide

●8. Saving and Restoring Configuration Parameters

❍8.1. Sending Parameters to a File

❍8.2. Restoring Saved Parameters

●9. Upgrading CMS Firmware

●10. Command Reference Guide

❍10.1. Command Conventions

❍10.2. Command Response

❍10.3. Command Summary

❍10.4. Command Set

Appendices

●A. RS232 Port Interface

●B. Specifications

●C. Customer Service

List of Figures

●2.1. Instrument Front Panel

●2.2. Instrument Back Panel

●3.1. The Supervisor Level Help Screen

●3.2. The Port Status Screen (Defaults Shown)

●4.1. Terminal Block Assembly (DC Units Only)

●4.2. CMS Application Example (Not to Scale)

●5.1. Port Configuration Menu (Port 2 Shown)

●5.2. Port Parameters Menu (Modem Mode)

●5.3. Network Parameters Menu (Supervisor Mode Only)

●5.4. IP Security Menu

●5.5. The Copy Port Parameters Menu

●6.1. The Port Status Screen (Supervisor Mode, Defaults Shown)

●6.2. The Port Diagnostics Screen (Defaults Shown)

●6.3. The Network Status Screen

●6.4. The Port Parameters Screen (RS232 Port Shown)

●A.1. RS232 Port Interface

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (5 of 59) [11/15/2000 10:52:02 AM]

Image 5

Contents CMS-16 Rack Mount Installation Nameplate Power WarningBattery Replacement Table of Contents WTI CMS-16 Console Management Switch -- Users Guide List of Figures AppendicesTypographic Conventions IntroductionBold Font Unit DescriptionFront Panel Back Panel Power Cable Receptacle Power SwitchGetting Started System SetUp Ports Apply Power to the CMSUsing Other Parameters for this Overview Optional Communication ParametersCommunicating with the CMS Unit Connecting your PC to the CMSDisplay Free Any Undefined Enter /H for Command Menu Connecting Power to the CMS Unit Hardware InstallationAC Powered Units DC Powered UnitsDefault Baud Rate Sw1, Sw2, Sw3 Configure Option SwitchesDefault Command Echo Sw7 Default Handshake Sw4, Sw5Default Response Message Format Sw6 Application Example Initialize Unit to Default SettingsConnecting Devices to the CMS CMS Application Example Not to Scale Access to the CMS Command Mode Configuration$ telnet 192.1.1.1 Enter Password FunctionsPort Passwords Supervisor PasswordDefining the Site ID and Supervisor Password Configuration Conventions Port ConfigurationPort Modes 3. RS232 Port Configuration MenusCTS/RTS Stop Bits Default =AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Telnet Port Parameters Network Port Configuration MenuNetwork Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Port Status Screen /S Status ScreensSave User Selected Parameters Port Status Screen Supervisor Mode, Defaults Shown Port Diagnostics Screen /SDPort Name Status Baud COM HS Mode BUF CTS Port Parameters Screens /W Network Status Screen /SNWP xx Enter Port Connection and Disconnection Any-to-Any ModeOperation Disconnecting Ports Enter Hunt Group Example Defining Hunt GroupsBuffer Mode Passive ModePort Buffers Reading Data from Buffer Mode PortsXx Enter Modem Mode Saving and Restoring Configuration ParametersRestoring Saved Parameters Sending Parameters to a FileUpgrading CMS Firmware Command Conventions Command Reference GuideTerse Verbose Command ResponseCommand Availability Supervisor User Command SummaryEnter Enter Command Mode Command SetConnect Enter+++Enter Resident Disconnect SequenceErase Buffer CP Copy RS232 Port ParametersThird Party Disconnect Help Default and TestSet System Parameters Set RS232 Port Parameters Display Site IDSet Network Port Parameters Reset Network Port SD Display Port DiagnosticsDisplay Port Status SN Display Network StatusDisplay Port Parameters Who UF Upgrade FirmwareSave Parameters Format /X Enter Exit Command ModeAppendix A. RS232 Port Interface Appendix C. Customer Service Appendix B. SpecificationsPower Stop Bits 1 orTrademarks Used in this Manual Trademark and Copyright Information

Related manuals

Manual 62 pages 40.13 Kb