HP StudioJet, FlexJet E manual Chapter, Getting Started

Page 13

Unless otherwise noted, diagrams and descriptions de- picting Ioline FlexJet E printer models also apply to the Ioline StudioJet in this manual.

Getting Started

Thank you for purchasing the Ioline FlexJet E or StudioJet printer.

This manual contains instructions and guidelines for setting up, operating and maintaining your Ioline printer. The following compo- nents are needed to create markers:

nA FlexJet E printer assembled according to the directions out- lined in the FlexJet E Printer or StudioJet Quick Start Guide.

nA computer system that is properly installed and has a func- tioning serial or USB port.

nApparel design software loaded into the computer according to the installation instructions.

nPrinting media and ink cartridges that are within the guidelines stated under the Operation chapter.

nDepending on the communications setup, Ioline FlexPlot soft- ware is required if your CAD software does not create compat- ible files.

CHAPTER 1

Overview

iNote

In order to output to the FlexJet E or StudioJet printer, your apparel design software must create plot files in HPGL 7475 or DM/PL format.Alternatively, you can output markers using the FlexPlot software, included with the printer. FlexPlot imports and converts a variety of file formats for output to your Ioline printer.

iNote

The Ioline Control Center and FlexPlot will only run on the Windows® 2000/XP/Vista operating systems. Most design software provides drivers for Ioline printers. Contact Ioline customer service if you need as- sistance with drivers.

Image 13

Contents User Guide User Notice Ioline Flexjet E Printers Table of Contents Routine Maintenance Glossary Index Page Page Safety & Cautions Visual Reference Guide KM N AB C D E F Getting Started ChapterIoline FlexJet E User Guide How The Ioline FlexJet E and StudioJet printers WorkUnpacking the Printer Printer AssemblyAssembling the Stand Attaching the Printer to the StandCable Connections Serial ConfigurationCOM Port Software Setup Options Other Serial Port SettingsInstallation Baud RateCAD Installing FlexPlot and the Control Center Power OnThis page intentionally left blank Start/Stop Keypad ControlsQuality CleanSet Origin Special Key Combinations Variety of settings are adjustable to fit specific needs Changing System SettingsControl Center OverviewFile Control Center Menu Bar FeaturesCommunications ToolsControl Center Menu Options Consumables General Guidelines Printing a MarkerSend marker/plot files Loading Paper on the FlexJet E Loading Paper on the StudioJetFlexJet E only Installing the Take-up Shaft2H+ FlexJet E Feeding PaperPositioning the Pinchwheels Tape Paper to theTake-up ShaftPositioning the pinchwheels Insert Front Dancer BarInsert Rear Dancer Bar2H+ FJE Models Only Pausing a Marker PlotSet an Origin Sending Plot FilesRemoving Markers from the Take-up Shaft Canceling a Marker PlotManually freeing the take-up shaft Manually Freeing Take-up ShaftReattach Paper To the Take-up Shaft Automatically Freeing the Take-Up ShaftPrinting to the Floor Cleaning the Platen and Traverse Cleaning the Drive ShaftSize Calibration Cleaning the Support BlocksPrepare the Printer See the Operation chapter Use the Control Center to Gather the Calibration Data Click on Done when finished Routine MaintenanceEnter the Calibration Data Prepare the Printer Cartridge CalibrationClick on Done when finished Motion Adjust Carriage Scan AlignmentFrame Gap Paper Scan Alignment Automatic Cleaning Procedure Cartridge Maintenance and HandlingCheck Cartridges Soft, fiberless, and moistened with deionized water Manual Cleaning ProcedureOpen the latch for the first cartridge and remove it Print Cartridge Storage Update the Firmware Reset Calibration Values Media Tracking General TroubleshootingLine Quality Printing QualitySerial Communication Troubleshooting Keypad Error CodesPrinter does not complete the marker Cause Common IssuesQuick Start Guide to level Regular or intermittent paper tearing Cause FlexJet E Models only This page intentionally left blank Getting Help Service & SupportYour Comments Are Requested Customer Service700 A.M. 500 P.M. U.S. Pacific Time End Notes Before you contact Support…This booklet is available from FCC WantsYou to KnowGlossary Panel See Frame Glossary This page intentionally left blank Arrow keys ix, 23, 24, 25, 37, 42, 44 Clean ix, 24, 33, 41, 46Calibration 27, 42-46, 49 Design software 15, 17, 19, 24, 28, 36, 51, 52, 54, 57, 61 Baud rate 18, 19, 25, 27, 28, 44, 52DM/PL 15, 19, 20 File formats 15, 19, 20 Feed shaft x, 30, 31, 35, 42, 55, 63EPS 27 PLT 27 PLX 27 IndexSet origin 24, 36, 37, 42, 44, 54, 56 Stalls xii, 29Media 15, 16, 51 Origin 16, 21, 24, 36, 37, 42, 44, 53, 54, 56Power switch xi, xiv, 21 Power cord xiv, 18, 21, 41Platen xi, xii, xiii, 33, 41, 55, 56 Frame 16, 28, 54Stop mode 23, 24, 25, 29, 37, 50 Service Station ix, xii, 21, 24, 33, 36, 46, 48, 50, 53Sensor xii, 25 Serial port xi, xiv, 15, 17, 18, 19, 25, 52Unroll v, 23, 25, 32, 37, 39, 50 Traverse xii, 41USB xi Index