HP FlexJet E, StudioJet manual User Notice

Page 2

USER NOTICE

Trademarks

Ioline, StudioJet and FlexJet E printers are trademarks of Ioline Corporation. HP is a trademark of the Hewlett-Packard Company. Other product names, logos, designs, titles, words or phrases mentioned within this publication may be trademarks, service marks, or trade names of Ioline Corporation or other entities and may be registered in certain jurisdictions including internationally.

Ioline Disclaimer

IOLINE CORPORATION PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL IOLINE, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF IOLINE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

Limit of Liability Statement

It is the responsibility of the operator of the printer to monitor the performance of the printer and main- tain it in proper working condition by following the instructions in this User Guide. It is the responsibility of the operator of the printer to follow all safety precautions and warnings that are described in this User Guide. Ioline Corporation is not responsible for injuries that may occur as a result of unsafe use. Ioline Corporation is not responsible for substandard operational performance as a result of failure to maintain the printer as described in this User Guide.

© 2003-2008 Ioline Corporation. All rights reserved. This manual may not be copied, photocopied, repro- duced, translated, transmitted or converted to any electronic or machine-readable form in whole or in part without prior written approval of Ioline Corporation.

Service and Support

If you require assistance with an Ioline product, your local Ioline dealer or authorized service center is ready to help. Support information is also available 24/7 on the Ioline Web site—or you may contact Ioline directly:

Ioline Corporation

14140 NE 200th Street

Woodinville,Washington 98072 U.S.A.

Ioline Customer Service Department

Monday through Friday

7:00 A.M. - 5:00 P.M. U.S. Pacific Time

Voice: 1.425.398.8282

Fax: 1.425.398.8383

support@ioline.com

www.ioline.com

Part Number 109619 Rev. 1

Page 1 Page 3
Image 2
Page 1 Page 3
Contents User Guide User Notice Ioline Flexjet E Printers Table of Contents Routine Maintenance Glossary Index Page Page Safety & Cautions Visual Reference Guide KM N AB C D E F Chapter Getting StartedHow The Ioline FlexJet E and StudioJet printers Work Ioline FlexJet E User GuideAssembling the Stand Printer AssemblyUnpacking the Printer Attaching the Printer to the StandCOM Port Serial ConfigurationCable Connections Installation Other Serial Port SettingsSoftware Setup Options Baud RateCAD Power On Installing FlexPlot and the Control CenterThis page intentionally left blank Keypad Controls Start/StopSet Origin CleanQuality Special Key Combinations Control Center Changing System SettingsVariety of settings are adjustable to fit specific needs OverviewCommunications Control Center Menu Bar FeaturesFile ToolsControl Center Menu Options Consumables Send marker/plot files Printing a MarkerGeneral Guidelines Loading Paper on the StudioJet Loading Paper on the FlexJet EInstalling the Take-up Shaft FlexJet E onlyFeeding Paper 2H+ FlexJet ETape Paper to theTake-up Shaft Positioning the PinchwheelsInsert Front Dancer Bar Positioning the pinchwheelsSet an Origin Pausing a Marker PlotInsert Rear Dancer Bar2H+ FJE Models Only Sending Plot FilesCanceling a Marker Plot Removing Markers from the Take-up ShaftManually Freeing Take-up Shaft Manually freeing the take-up shaftAutomatically Freeing the Take-Up Shaft Reattach Paper To the Take-up ShaftPrinting to the Floor Cleaning the Drive Shaft Cleaning the Platen and TraversePrepare the Printer See the Operation chapter Cleaning the Support BlocksSize Calibration Enter the Calibration Data Click on Done when finished Routine MaintenanceUse the Control Center to Gather the Calibration Data Cartridge Calibration Prepare the PrinterFrame Gap Paper Scan Alignment Motion Adjust Carriage Scan AlignmentClick on Done when finished Check Cartridges Cartridge Maintenance and HandlingAutomatic Cleaning Procedure Open the latch for the first cartridge and remove it Manual Cleaning ProcedureSoft, fiberless, and moistened with deionized water Print Cartridge Storage Update the Firmware Reset Calibration Values General Troubleshooting Media TrackingSerial Communication Printing QualityLine Quality Keypad Error Codes TroubleshootingCommon Issues Printer does not complete the marker CauseQuick Start Guide to level Regular or intermittent paper tearing Cause FlexJet E Models only This page intentionally left blank Service & Support Getting Help700 A.M. 500 P.M. U.S. Pacific Time Customer ServiceYour Comments Are Requested Before you contact Support… End NotesFCC WantsYou to Know This booklet is available fromGlossary Panel See Frame Glossary This page intentionally left blank Calibration 27, 42-46, 49 Clean ix, 24, 33, 41, 46Arrow keys ix, 23, 24, 25, 37, 42, 44 DM/PL 15, 19, 20 Baud rate 18, 19, 25, 27, 28, 44, 52Design software 15, 17, 19, 24, 28, 36, 51, 52, 54, 57, 61 EPS 27 PLT 27 PLX 27 Feed shaft x, 30, 31, 35, 42, 55, 63File formats 15, 19, 20 IndexMedia 15, 16, 51 Stalls xii, 29Set origin 24, 36, 37, 42, 44, 54, 56 Origin 16, 21, 24, 36, 37, 42, 44, 53, 54, 56Platen xi, xii, xiii, 33, 41, 55, 56 Power cord xiv, 18, 21, 41Power switch xi, xiv, 21 Frame 16, 28, 54Sensor xii, 25 Service Station ix, xii, 21, 24, 33, 36, 46, 48, 50, 53Stop mode 23, 24, 25, 29, 37, 50 Serial port xi, xiv, 15, 17, 18, 19, 25, 52USB xi Index Traverse xii, 41Unroll v, 23, 25, 32, 37, 39, 50
Top Page Image Contents