HP StudioJet, FlexJet E manual Insert Front Dancer Bar, Positioning the pinchwheels

Page 33

Pinchwheel

	White Driveshaft Markers
Drive Shaft	Figure 22. Positioning the pinchwheels.
Drive Shaft
Segment	Drive Shaft
	Bearing

3.Make sure that the paper roll is tight on the feed shaft.

4.Move the pinchwheels into their proper positions over a tread and under the white markers on the traverse rail. (See Figure 22.) Do not place pinchwheels over drive shaft bearings.)

5.Lower the pinchwheels.

Insert Front Dancer Bar

(FlexJet E only)

1.With the pinchwheels lowered, hold the paper in place over the rear top bar.

2.Insert the front dancer bar into the dancer bar channel.

Front Dancer Bar (Silver light rod)

Figure 24. Inserting the dancer bar.

Chapter 3: Operation 35

iNote

Ensure that the paper roll is cen- tered on the feed shaft.

Image 33

Contents User Guide User Notice Ioline Flexjet E Printers Table of Contents Routine Maintenance Glossary Index Page Page Safety & Cautions Visual Reference Guide KM N AB C D E F Getting Started ChapterIoline FlexJet E User Guide How The Ioline FlexJet E and StudioJet printers WorkUnpacking the Printer Printer AssemblyAssembling the Stand Attaching the Printer to the StandSerial Configuration Cable ConnectionsCOM Port Software Setup Options Other Serial Port SettingsInstallation Baud RateCAD Installing FlexPlot and the Control Center Power OnThis page intentionally left blank Start/Stop Keypad ControlsClean QualitySet Origin Special Key Combinations Variety of settings are adjustable to fit specific needs Changing System SettingsControl Center OverviewFile Control Center Menu Bar FeaturesCommunications ToolsControl Center Menu Options Consumables Printing a Marker General GuidelinesSend marker/plot files Loading Paper on the FlexJet E Loading Paper on the StudioJetFlexJet E only Installing the Take-up Shaft2H+ FlexJet E Feeding PaperPositioning the Pinchwheels Tape Paper to theTake-up ShaftPositioning the pinchwheels Insert Front Dancer BarInsert Rear Dancer Bar2H+ FJE Models Only Pausing a Marker PlotSet an Origin Sending Plot FilesRemoving Markers from the Take-up Shaft Canceling a Marker PlotManually freeing the take-up shaft Manually Freeing Take-up ShaftReattach Paper To the Take-up Shaft Automatically Freeing the Take-Up ShaftPrinting to the Floor Cleaning the Platen and Traverse Cleaning the Drive ShaftCleaning the Support Blocks Size CalibrationPrepare the Printer See the Operation chapter Click on Done when finished Routine Maintenance Use the Control Center to Gather the Calibration DataEnter the Calibration Data Prepare the Printer Cartridge CalibrationMotion Adjust Carriage Scan Alignment Click on Done when finishedFrame Gap Paper Scan Alignment Cartridge Maintenance and Handling Automatic Cleaning ProcedureCheck Cartridges Manual Cleaning Procedure Soft, fiberless, and moistened with deionized waterOpen the latch for the first cartridge and remove it Print Cartridge Storage Update the Firmware Reset Calibration Values Media Tracking General TroubleshootingPrinting Quality Line QualitySerial Communication Troubleshooting Keypad Error CodesPrinter does not complete the marker Cause Common IssuesQuick Start Guide to level Regular or intermittent paper tearing Cause FlexJet E Models only This page intentionally left blank Getting Help Service & SupportCustomer Service Your Comments Are Requested700 A.M. 500 P.M. U.S. Pacific Time End Notes Before you contact Support…This booklet is available from FCC WantsYou to KnowGlossary Panel See Frame Glossary This page intentionally left blank Clean ix, 24, 33, 41, 46 Arrow keys ix, 23, 24, 25, 37, 42, 44Calibration 27, 42-46, 49 Baud rate 18, 19, 25, 27, 28, 44, 52 Design software 15, 17, 19, 24, 28, 36, 51, 52, 54, 57, 61DM/PL 15, 19, 20 File formats 15, 19, 20 Feed shaft x, 30, 31, 35, 42, 55, 63EPS 27 PLT 27 PLX 27 IndexSet origin 24, 36, 37, 42, 44, 54, 56 Stalls xii, 29Media 15, 16, 51 Origin 16, 21, 24, 36, 37, 42, 44, 53, 54, 56Power switch xi, xiv, 21 Power cord xiv, 18, 21, 41Platen xi, xii, xiii, 33, 41, 55, 56 Frame 16, 28, 54Stop mode 23, 24, 25, 29, 37, 50 Service Station ix, xii, 21, 24, 33, 36, 46, 48, 50, 53Sensor xii, 25 Serial port xi, xiv, 15, 17, 18, 19, 25, 52Traverse xii, 41 Unroll v, 23, 25, 32, 37, 39, 50USB xi Index