HP StudioJet manual Feeding Paper, 2H+ FlexJet E

Page 31

take-up shaft into place until it is seated in the support block.

Feeding Paper

(FlexJet E only)

Figure 20 represents the proper paper path. The left side of the dia- gram shows the paper path for a 1H FlexJet E. The right side shows the proper path for a FlexJet E with 2 or more heads.

1.Remove any printed markers from the take-up shaft and make sure the carriage is parked in the Service Station before feeding the paper. (To park the carriage, press Start/Stop. Wait for the OK light to turn red and press the Clean button.)

2.If the pinchwheels are lowered, raise them by pushing the pinchwheel lever away from the machine.

3.Pull a long leader of paper off of the paper roll and insert it through the stand, behind the plotting head between the platen and pinchwheels.

4.Temporarily lock the paper in place by pulling the pinchwheel lever toward the machine to lower the pinchwheels.

Front

Dancer Bar

Take-up

Shaft

Feed Roll

Proper Paper Path

 

 

 

 

 

 

 

Proper Paper Path

 

 

1H FlexJet E

 

 

 

 

2H+ FlexJet E

Figure 20. The correct paper feeding path on the Ioline FlexJet E printers. (See the StudioJet Quick Start Guide for paper path instructions for the StudioJet.)

Chapter 3: Operation 33

Image 31
Contents User Guide User Notice Ioline Flexjet E Printers Table of Contents Routine Maintenance Glossary Index Page Page Safety & Cautions Visual Reference Guide KM N AB C D E F Getting Started ChapterIoline FlexJet E User Guide How The Ioline FlexJet E and StudioJet printers WorkAttaching the Printer to the Stand Printer AssemblyUnpacking the Printer Assembling the StandCable Connections Serial ConfigurationCOM Port Baud Rate Other Serial Port SettingsSoftware Setup Options InstallationCAD Installing FlexPlot and the Control Center Power OnThis page intentionally left blank Start/Stop Keypad ControlsQuality CleanSet Origin Special Key Combinations Overview Changing System SettingsVariety of settings are adjustable to fit specific needs Control CenterTools Control Center Menu Bar FeaturesFile CommunicationsControl Center Menu Options Consumables General Guidelines Printing a MarkerSend marker/plot files Loading Paper on the FlexJet E Loading Paper on the StudioJetFlexJet E only Installing the Take-up Shaft2H+ FlexJet E Feeding PaperPositioning the Pinchwheels Tape Paper to theTake-up ShaftPositioning the pinchwheels Insert Front Dancer BarSending Plot Files Pausing a Marker PlotInsert Rear Dancer Bar2H+ FJE Models Only Set an OriginRemoving Markers from the Take-up Shaft Canceling a Marker PlotManually freeing the take-up shaft Manually Freeing Take-up ShaftReattach Paper To the Take-up Shaft Automatically Freeing the Take-Up ShaftPrinting to the Floor Cleaning the Platen and Traverse Cleaning the Drive ShaftSize Calibration Cleaning the Support BlocksPrepare the Printer See the Operation chapter Use the Control Center to Gather the Calibration Data Click on Done when finished Routine MaintenanceEnter the Calibration Data Prepare the Printer Cartridge CalibrationClick on Done when finished Motion Adjust Carriage Scan AlignmentFrame Gap Paper Scan Alignment Automatic Cleaning Procedure Cartridge Maintenance and HandlingCheck Cartridges Soft, fiberless, and moistened with deionized water Manual Cleaning ProcedureOpen the latch for the first cartridge and remove it Print Cartridge Storage Update the Firmware Reset Calibration Values Media Tracking General TroubleshootingLine Quality Printing QualitySerial Communication Troubleshooting Keypad Error CodesPrinter does not complete the marker Cause Common IssuesQuick Start Guide to level Regular or intermittent paper tearing Cause FlexJet E Models only This page intentionally left blank Getting Help Service & SupportYour Comments Are Requested Customer Service700 A.M. 500 P.M. U.S. Pacific Time End Notes Before you contact Support…This booklet is available from FCC WantsYou to KnowGlossary Panel See Frame Glossary This page intentionally left blank Arrow keys ix, 23, 24, 25, 37, 42, 44 Clean ix, 24, 33, 41, 46Calibration 27, 42-46, 49 Design software 15, 17, 19, 24, 28, 36, 51, 52, 54, 57, 61 Baud rate 18, 19, 25, 27, 28, 44, 52DM/PL 15, 19, 20 Index Feed shaft x, 30, 31, 35, 42, 55, 63File formats 15, 19, 20 EPS 27 PLT 27 PLX 27Origin 16, 21, 24, 36, 37, 42, 44, 53, 54, 56 Stalls xii, 29Set origin 24, 36, 37, 42, 44, 54, 56 Media 15, 16, 51Frame 16, 28, 54 Power cord xiv, 18, 21, 41Power switch xi, xiv, 21 Platen xi, xii, xiii, 33, 41, 55, 56Serial port xi, xiv, 15, 17, 18, 19, 25, 52 Service Station ix, xii, 21, 24, 33, 36, 46, 48, 50, 53Stop mode 23, 24, 25, 29, 37, 50 Sensor xii, 25Unroll v, 23, 25, 32, 37, 39, 50 Traverse xii, 41USB xi Index