HP FlexJet E, StudioJet manual Cleaning the Support Blocks, Size Calibration

Page 40

42 Ioline FlexJet E User Guide

CAUTION

Never touch the take-up key or flanged coupling while they are rotating.

Serious personal injury could result.Turn power off first.

iNote

The Scale command does not effect calibration values.

Cleaning the Support Blocks

(FlexJet E Only)

When dust and paper residue will accumulate on the take-up and feed shaft support blocks, frequent feed shaft jams can occur. Per- form this procedure when debris inhibits easy rotation of the shaft.

1.Turn off power to the printer.

2.Remove the feed shaft and the take-up shaft.

3.Dampen a lint-free cloth with isopropyl (pharmacy) alcohol and gently wipe the plastic support blocks until accumulated residue is removed.

4.Apply a light coating of grease to the plastic feed shaft sup- port block. White Lithium grease is supplied with the printer. 3-in-1brand oil is also a very good lubricant for the feed block.

5.Wipe down both ends of the feed and take-up shafts before reinstalling them.

Size Calibration

Over time, the printer may require calibration to account for normal wear. Calibration adjusts the output to match design intent.

Prepare the Printer (See the Operation chapter)

1.Load the printer with, at minimum, 46-in wide paper.

2.Install ink cartridges.

3.Using the Arrow keys, move the carriage so that the carriage notch is positioned about 1 inch from the right edge of the paper.

4.Press the Set Origin key to put the printer in START (green light) mode.

Figure 29. Calibration screen in Control Center.

Image 40
Contents User Guide User Notice Ioline Flexjet E Printers Table of Contents Routine Maintenance Glossary Index Page Page Safety & Cautions Visual Reference Guide KM N AB C D E F Chapter Getting StartedHow The Ioline FlexJet E and StudioJet printers Work Ioline FlexJet E User GuidePrinter Assembly Unpacking the PrinterAssembling the Stand Attaching the Printer to the StandCable Connections Serial ConfigurationCOM Port Other Serial Port Settings Software Setup OptionsInstallation Baud RateCAD Power On Installing FlexPlot and the Control CenterThis page intentionally left blank Keypad Controls Start/StopQuality CleanSet Origin Special Key Combinations Changing System Settings Variety of settings are adjustable to fit specific needsControl Center OverviewControl Center Menu Bar Features FileCommunications ToolsControl Center Menu Options Consumables General Guidelines Printing a MarkerSend marker/plot files Loading Paper on the StudioJet Loading Paper on the FlexJet EInstalling the Take-up Shaft FlexJet E onlyFeeding Paper 2H+ FlexJet ETape Paper to theTake-up Shaft Positioning the PinchwheelsInsert Front Dancer Bar Positioning the pinchwheelsPausing a Marker Plot Insert Rear Dancer Bar2H+ FJE Models OnlySet an Origin Sending Plot FilesCanceling a Marker Plot Removing Markers from the Take-up ShaftManually Freeing Take-up Shaft Manually freeing the take-up shaftAutomatically Freeing the Take-Up Shaft Reattach Paper To the Take-up ShaftPrinting to the Floor Cleaning the Drive Shaft Cleaning the Platen and TraverseSize Calibration Cleaning the Support BlocksPrepare the Printer See the Operation chapter Use the Control Center to Gather the Calibration Data Click on Done when finished Routine MaintenanceEnter the Calibration Data Cartridge Calibration Prepare the PrinterClick on Done when finished Motion Adjust Carriage Scan AlignmentFrame Gap Paper Scan Alignment Automatic Cleaning Procedure Cartridge Maintenance and HandlingCheck Cartridges Soft, fiberless, and moistened with deionized water Manual Cleaning ProcedureOpen the latch for the first cartridge and remove it Print Cartridge Storage Update the Firmware Reset Calibration Values General Troubleshooting Media TrackingLine Quality Printing QualitySerial Communication Keypad Error Codes TroubleshootingCommon Issues Printer does not complete the marker CauseQuick Start Guide to level Regular or intermittent paper tearing Cause FlexJet E Models only This page intentionally left blank Service & Support Getting HelpYour Comments Are Requested Customer Service700 A.M. 500 P.M. U.S. Pacific Time Before you contact Support… End NotesFCC WantsYou to Know This booklet is available fromGlossary Panel See Frame Glossary This page intentionally left blank Arrow keys ix, 23, 24, 25, 37, 42, 44 Clean ix, 24, 33, 41, 46Calibration 27, 42-46, 49 Design software 15, 17, 19, 24, 28, 36, 51, 52, 54, 57, 61 Baud rate 18, 19, 25, 27, 28, 44, 52DM/PL 15, 19, 20 Feed shaft x, 30, 31, 35, 42, 55, 63 File formats 15, 19, 20EPS 27 PLT 27 PLX 27 IndexStalls xii, 29 Set origin 24, 36, 37, 42, 44, 54, 56Media 15, 16, 51 Origin 16, 21, 24, 36, 37, 42, 44, 53, 54, 56Power cord xiv, 18, 21, 41 Power switch xi, xiv, 21Platen xi, xii, xiii, 33, 41, 55, 56 Frame 16, 28, 54Service Station ix, xii, 21, 24, 33, 36, 46, 48, 50, 53 Stop mode 23, 24, 25, 29, 37, 50Sensor xii, 25 Serial port xi, xiv, 15, 17, 18, 19, 25, 52Unroll v, 23, 25, 32, 37, 39, 50 Traverse xii, 41USB xi Index