HP Vectra VL 5/xxx Installing Accessory Boards, Configuring Accessory Boards with Plug and Play

Page 47

CAUTION

2 How to Install Accessories In Your PC

Installing Accessory Boards

Installing Accessory Boards

Static electricity can damage electronic components. Turn all equipment off. Don’t let your clothes touch the accessory. To equalize the static electricity, rest the accessory bag on top of the computer while you are removing the accessory from the bag. Handle the accessory as little as possible and with care.

The PC has four accessory board slots:

•Slot 1 (the top slot) can be used for a full-length 32-bit PCI board

•Slot 2 can be used for full-length 32-bit PCI boards

•Slot 3 can be used for either a full-length 32-bit PCI or a full-length 16-bit ISA board

•Slot 4 (the bottom slot) can be used for 16-bit ISA boards (16 cm/6.3-inch maximum length).

Configuring Accessory Boards with Plug and Play

Plug and Play is an industry standard for automatically configuring your PC's hardware resources and the accessory boards installed in it. If your operating system supports Plug and Play, your PC has configurable support for Plug and Play in the BIOS.

All PCI accessory boards are Plug and Play, although not all ISA boards are. Check the accessory board’s documentation if you are unsure.

When you start your PC after installing an accessory board, the Plug and Play BIOS automatically detects which hardware resources (IRQs, DMAs, memory ranges, and I/O addresses) are used by the system- based components.

Configuring non-Plug and Play ISA Accessory Boards

If you install an ISA accessory board that is not Plug and Play you will need to configure the board before your PC can use it.

Refer to the documentation supplied with the operating system for details on your operating system’s capabilities and restrictions concerning how to configure non-Plug and Play accessory boards.

35

Image 47

Contents User’s Guide Page User’s Guide Who this Manual is For Important Safety InformationImportant Ergonomic Information Page Contents Removing and Replacing the Cover Installing Mass Storage DevicesInstalling Accessory Boards If Your PC Has a Software Problem Hewlett Packard Support and Information Services HP Setup ProgramGlossary Index Xii Setting Up and Using Your PC Try to move it without help When you receive your PC, unpack all the componentsAccessories Unpacking Your PCConnections for Models with Integrated Video Display Connecting the Mouse, Keyboard, Display and PrinterConnections for Models with MGA Millennium Video Board Electronic servicesConnecting to a Network Connecting Audio Accessories Grounded outlet Connecting the Power CablesScsi hard disk drive, this light will not work Press this button to turn the power on or off to your PCYour PC’s Hardware Control Panel Your PC’s hardware control panel is on the front of your PCStarting Your PC Starting and Stopping Your PCInitializing Your Software Starting the PC for the First TimeAfter Your PC Has Restarted Stopping Your PC Creating Master DiskettesSetting an Administrator Password Setting PasswordsAction Setting a User PasswordPassword, on Then pressAdditional Information and Help Using Power ManagementSetting Up and Using Your PC Additional Information and Help How to Install Accessories In Your PC Video Memory Accessories You Can InstallCache Memory Up to Four Accessory Boards Front-Access Device ShelfRemoving the Cover Replacing the Cover after Installing AccessoriesCheck that you have installed all your accessories Removing and Replacing the CoverMoving and Replacing the Power Supply Static electricity can damage electronic components Installing MemoryInstalling Main Memory Refer to All cables and power cordsIdentified here as C is the one closest to the processor Clip and pull the module forward and out of the socketHandle the accessory as little as possible and with care Installing an Optional Cache Memory ModuleUpgrade this to 512 KB Installing a Video Memory Upgrade Integrated Video Models To Install Video Memory ModulesAfter Installing a Video Memory Upgrade Upgrading the MGA Millennium Board Memory Switch Use Switch Block to Connecting IDE Devices Installing Mass Storage DevicesExamples of multiple IDE drive combinations Jumper SettingsConfiguring an IDE Device After Installation Configuration Connections to data cablesInstalling an IDE Hard Disk Drive in the Rear Shelf Installing an IDE Hard Disk Drive in the Bottom Shelf Page Tape drive can be installed in the bottom shelf Installing a Tape Drive in the Bottom ShelfPage Configuring non-Plug and Play ISA Accessory Boards Installing Accessory BoardsConfiguring Accessory Boards with Plug and Play Installing the Board Installing an Accessory Board refer to facing Installing a BNC Coax Adapter Remove the metal plug Remove the nut To Install a BNC Coax AdapterInstalling an OverDrive Processor Processor Cables and power cordsInstalling the Security Bracket Troubleshooting Your PC HP Summary Screen Solving ProblemsIf Your PC Does Not Start Properly Display is Blank and There Are No Error MessagesCorrectly installed If You Cannot Start Your PC from a Modem If a Post Error Message is DisplayedClear the configuration Clearing the PC’s Configuration MemoryIf Your Display is Blurred or Unreadable If Your PC Has a Hardware ProblemIf You Cannot Turn Off Your PC Display Does Not Work ProperlyIf Nothing is Displayed on the Screen Other Display ProblemsEnsure that the mouse is correctly connected If Your Keyboard Does Not WorkIf Your Mouse Does Not Work Ensure that the keyboard is correctly connectedIf Your Printer Does Not Work If the Flexible Disk Drive Does Not Work If the Hard Disk Does Not Work If the Hard DiskNot Work CD-ROM Drive is Idle If the CD-ROM Drive Has a ProblemCable connections or jumper settings CD-ROM Drive Does Not WorkIf an Accessory Board Does Not Work If You Have Forgotten Your Password If Your PC Has a Software ProblemIf the Date and Time are Incorrect If You Have a Network ProblemIf Your Application Software Does Not Work No Sound When Running Any Applications If Your PC Has an Audio ProblemSounds MS-DOS Games Give Not enough memory ErrorsChanging the Battery Strip supplied External battery as followsCable to the battery connector on the system board Technical Information System Board SwitchesBus Switch1 All measurements are in watts rms Power ConsumptionIRQs, DMAs, and I/O Addresses Used by Your PC Integrated Video Graphic Information HP Setup ProgramHewlett Packard Support and Information Services Introduction Service Means of AccessHP SupportPack Your HP Authorized ResellerRegion Phone Number Fax Number HP Support Assistant CD-ROMAt the CompuServe ! prompt, type GO HP Hewlett-Packard Information ServicesHP Forum on CompuServe HP Forum on America Online World-Wide Web URL HP BBS LibraryHP World Wide Web Site Country Number Baud RateCountry/Region Access MethodHP FAXback on Demand-HP First HP Audio Tips USA only HP Automated Support DirectoryAustralia Asia Pacific Ordering Drivers and Bios on DisketteEurope HP Support Services Country1 Language Local Number Hewlett-Packard Telephone SupportCustomer Support Center Number is +1 970Number Method of Payment Charge Type Lifeline Telephone SupportHP Network Phone-in Support Service NPS Covered Time Available From SummaryAsia Hewlett-Packard Marketing HeadquartersPage Glossary Glossary Computer is running as an unattended network server From reflecting back along the cable Index LAN IndexRegulatory Information and Warranty Regulatory Information FCC for USA only Noise Declaration for Germany HP Hardware Warranty Customer Responsibilities HP Software Product License Agreement HP Software Product Limited Warranty Your HP Vectra PC Physical Characteristics Part Number D4550-90001