HP 8753ET manual General characteristics

Page 20

General characteristics

Front panel connectors

HP 8753ES test ports (without Option 011) Connector type 7 mm, precision

Impedance 50 ohms (nominal)

HP 8753ES Option 011 test ports

Connector type Type-N female

Impedance 50 ohms (nominal)

HP 8753ES Option 075 test ports

Connector type

Type-N female

Impedance

75 ohms (nominal)

HP 8753ET test ports

Type-N female

Connector type

Impedance

50 ohms (nominal)

Probe power

+15V ±2% 400 mA

 

(combined load for both

 

probe connections)

 

-12.6V ±5.5% 300 mA

 

(combined load for both

 

probe connections)

Rear-panel connectors

 

External reference frequency input (EXT REF INPUT)

Frequency

1, 2, 5, and 10 MHz

 

(±200 Hz at 10 MHz)

Level

-10 dBm to +20 dBm, (typical)

Impedance

50 ohms

Connector

BNC (f)

High-stability frequency reference output

(Option 1D5)

10.0000 MHz

Frequency

Frequency stability

±0.05 ppm

(0 ˚C to 55 ˚C)

 

Daily aging rate

<3x10-9/day

(after 30 days)

Yearly aging rate

0.5 ppm/year

Output

0 dBm minimum

Nominal output

50 Ω Connector BNC (f)

impedance

External auxiliary input (AUX INPUT)

Input voltage limits -10V to +10V

External AM input (EXT AM)

±1 volt into a 5 k Ω resistor, 1 kHz maximum, resulting in approximately 8 dB/volt amplitude modulation.

BNC (f) connector.

External trigger (EXT TRIGGER)

Triggers on a negative TTL transition or contact closure to ground. BNC (f) connector.

Test sequence output (TEST SEQ)

By default, this connector outputs a TTL end-of-sweep signal. It can also be programmed by the user in a test sequence to output a user-defined TTL signal. BNC (f) connector.

Limit test output (LIMIT TEST)

This connector outputs a TTL signal of the limit test results. Pass: TTL high. Fail: TTL low. BNC (f) connec- tor.

Test-port bias input (BIAS CONNECT) (HP 8753ES only)

Maximum voltage

+30 VDC

Maximum current

±200 mA

(no degradation in RF specs)

Maximum current

±1 A

Connector

BNC (f)

VGA video output (EXT MON)

This connector drives external VGA monitors.

GP-IB

This connector allows communications with compati- ble devices including external controllers, printers, plotters, disk drives, and power meters.

Parallel port

This 25-pin female connector is used with parallel peripherals. It can also be used as a general purpose I/O port.

RS-232C

This 9-pin male connector is used with serial peripherals.

DIN keyboard

This mini-DIN connector is used for adding an IBM PC-AT compatible keyboard.

Test set interconnect

This connector is used to connect an HP 8753ES Option 011 to the HP 85046A/B or 85047A test set. HP 8753ES analyzers without Option 011 can use sig- nal levels on this connector for sequencing or general purpose I/O applications.

Internal memory

Typical data retention time with 3V, 1.2 Ah battery:

At 25 ˚C

11904 days (32.6 years)

At 40 ˚C

1244 days (3.4 years)

At 70 ˚C

250 days (0.68 year)

Line power

48 Hz to 66 Hz

115V nominal (90V to 132V) or 230V nominal

(198V to 264V).

280 VA max.

1.

Fmax is the upper frequency limit of the associated test set.

 

2.

Degrees, specified as deviation from linear phase.

 

20

 

 

 

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Specifications Table of contents Measurement port characteristics Definitions and test conditionsDynamic range Measurement uncertaintySystem performance summaries HP 8753ES 50-ohm systemsMm test ports Network analyzer HP 8753ESType-N test ports Calibration kit HP 85032B Test-port cables HP 11857DCalibration kit HP 85033D Test-port cables HP 11857D Frequency rangeCalibration kit HP 85036B Test-port cables HP 11857B HP 8753ES 75-ohm systemsNetwork analyzer Type-F test ports Calibration kit HP 85039B Test-port cables HP 11857BMeasurement port characteristics KHz to 16 MHz 100 dB MHz to 3 GHz 110 dB GHz to 6 GHz 105 dBTest port input characteristics HP 8753ES specificationsTest-port output characteristics7 Characteristics Phase characteristicsCW time sweep only KHz to 6 GHzTest port input characteristics Option HP 8753ES Option 011 specificationsTest port output characteristics KHz to 3 GHz To -35 dBm GHz to 6 GHz To -30 dBm 20 kHzFrequency CW time sweep onlyHP 8753ET specifications Test-port output characteristicsKHz to 3 GHz Option 006 300 kHz to 6 GHzTest-port input characteristics Magnitude characteristics±500 dB ±180˚HP 8753ET/ES supplemental characteristics Group delay characteristicsMeasurement Source controlDisplay control Data accuracy enhancementData averaging Trace functions StorageData hardcopy System capabilitiesRemote programming Test sequencesTime-domain Option This stimulus is also used to measure low-pass devicesGeneral characteristics Options HP 85046A/B S-parameter test sets Test set specifications for OptionHP 85046A/B Specifications Specifications HP 85047A S-parameter test set+20 dBm +30 dBmAccessories HP 85039B type-F calibration kit Specifications HP 85038 family of calibration kitsHP 11906B 7-16 to 50-Ohm type-N adapter kit HP 11906C 7-16 to 7-mm adapter kitVerification kits Test-port return cablesHP 85024A high-frequency probe Ohm accessory kitsRF limiter HP 8347A RF amplifier DimensionsWeight

8753ET specifications

The HP 8753ET is a sophisticated vector network analyzer designed to meet the demands of RF and microwave engineering applications. This instrument is renowned for its ability to provide high-performance measurements in a compact form factor, making it a favorite among engineers and technicians alike.

One of the main features of the HP 8753ET is its ability to perform a wide array of network analysis functions. It supports S-parameter measurements, allowing for the characterization of the linearity and performance of RF circuits. With the ability to measure reflection, transmission, and impedance characteristics, users can gain deep insights into their device under test (DUT).

An essential aspect of the HP 8753ET is its frequency range capability. It typically covers frequencies from 300 kHz to 6 GHz, which is ideal for a vast range of applications, including telecommunications, radar, and electronic warfare.

The HP 8753ET is equipped with advanced analysis features such as time-domain reflectometry (TDR) and gating capabilities. This enables engineers to identify and analyze impedance mismatches and faults over a defined time window, helping to troubleshoot and optimize RF systems effectively.

Another notable technology integrated into the HP 8753ET is its user-friendly interface that combines an easy-to-navigate display with direct access to measurement functions. This minimizes the learning curve for new users while enhancing productivity for experienced professionals.

The analyzer also supports various calibration techniques, ensuring accurate and repeatable measurements. The built-in calibration kits help improve the reliability of the results while compensating for any systematic errors associated with the test setup.

Additional characteristics of the HP 8753ET include its capability for both single-port and two-port measurements. This versatility allows users to conduct a complete array of S-parameter measurements with confidence.

Furthermore, the HP 8753ET features a storage function that allows users to save and recall measurement setups and results. This capability streamlines workflows and provides easy access to historical data for review or further analysis.

Ultimately, the HP 8753ET stands out as an essential tool for engineers in the RF and microwave domain. Its combination of high-performance measurement capabilities, an intuitive interface, and flexibility makes it a preferred choice for anyone seeking reliable and thorough network analysis in their testing and development projects.
Top Page Image Contents