HP GS1280 manual Power Distribution Units Mandatory, Type a, Type B

QuickSpecs

HP AlphaServer GS1280 Systems

GS Options

NOTES:

1.One High Performance I/O Drawer can be used by up to four separate hard partitions. Each of the four I/O connections (and two associated PCI-X slots) in the High Performance I/O Drawer can be independently controlled (e.g. power on/off) in conjunction with a separate partition.

2.A Master I/O Drawer consists of a Standard or High Performance I/O Drawer plus a Combination Adapter in one slot. The Combination Adapter provides an Ultra3 SCSI connection for two disks and a DVD/CD-RW drive in the drawer, plus a USB connection for keyboard, mouse, and monitor. The Master I/O Drawer is required for all GS1280 systems integrated at the manufacturing plant by HP. If the final system configuration does not require these I/O devices, the Combination Adapter may be removed and replaced with the following alternatives:

System Boot - External storage or network boot can be used in place of the disk storage internal to the I/O Drawer.

Software Load - Software can be loaded over the network from a disk on another system or directly from a CD reader attached to another system by using remote mount.

User I/O - User access via a network connection can be used in place of the direct connection via the USB port.

3.The two disks in the Master I/O Drawer can only be connected to the system via the Combination Adapter's Ultra3 SCSI connection. The I/O Drawer design does not permit connection from other storage adapters, such as a RAID adapter, that might be installed in the I/O Drawer.

4.Each Master I/O Drawer supports up to two, optional, hard disk drives. See the Disks step of the ES/GS Common Options section of this QuickSpec for the selection of supported disk drives.

Step 6 - Power Distribution Units - Mandatory

			GS1280 Model	GS1280 Model	GS1280 Model	GS1280 Model
			8	16	32	64
			DA/DY-1280A-	DA/DY-1280A-	DA/DY-1280A-	DA/DY-1280A-
			AA	BA	CC	BD
Type A	North America/Japan 200				2 required	2 required
Power Distribution	-208V, NEMA L21-30P	3X-H7606-	1 required	2 required	(provides	(provides
Units	30A; 3 x C19 outlets plus	AA			receptacles for	receptacles for
			(provides	(provides
Select one variant.	24 x C13 outlets				power cords	power cords
			receptacles for	receptacles for
					from I/O	from I/O
	International 380/415V Y,		power cords	power cords
					Drawers, LAN	Drawers, LAN
	IEC 309 32A; 3 x C19	3X-H7606-	from all system	from all system
					Hub, and	Hub, and
	outlets plus 24 x C13	AB	components)	components)	storage	storage
	outlets				shelves)	shelves)
Type B	North America/Japan	3X-H7606-	Not applicable	Not applicable	2 required	4 required
Power Distribution	200 - 208V, IEC 309 60A	BA			(for M32/M64	(for M32/M64
Units					Dual AC power	Dual AC power
Select one variant.	International	3X-H7606-			supply	supply
	380/415V Y, IEC 309	BB			exclusively for	exclusively for
	32A				8P system	8P system
					drawers)	drawers)

NOTES:

1.Select the same power supply voltage variant for both Type A and Type B Power Distribution Units, e.g. both 200- 208V or both 380/415V.

2.IEC 309 is a general spec that can encompass 3 different pin types. The 3X-H7606-BA PDU uses the Hubbell 460P9W, a 4 pin connector.

3.The 3X-H7606-AA PDU uses an L21-30P 30 amp plug, Hubbell 2811, a 4 pin connector.

DA - 11921 Worldwide — Version 24 — July 23, 2007 Page 15