HP C7288, C7250, C7280 manual Create a network profile for other operating systems

Page 16

Chapter 2

d. Make sure that the check box is not selected next to The key is provided for me automatically. If it is selected, click the check box to clear it.

e. In the Network key box, type a WEP key that has exactly 5 or exactly 13 alphanumeric (ASCII) characters. For example, if you enter 5 characters, you might enter ABCDE or 12345. Or, if you enter 13 characters, you might enter ABCDEF1234567. (12345 and ABCDE are examples only. Select a combination of your choosing.)

Alternatively, you can use HEX (hexadecimal) characters for the WEP key. A HEX WEP key must be 10 characters for 40 bit encryption, or 26 characters for 128 bit encryption.

f. In the Confirm network key box, type the same WEP key you typed in the previous step.

g. Write down the WEP key exactly as you typed it, including uppercase and lowercase letters.

NOTE: You must remember the exact uppercase (capital) and lowercase (small) letters. If you enter your WEP key incorrectly on the HP All-in-One, the wireless connection will fail.

h. Select the check box for This is a computer-to-computer (ad hoc) network; wireless access points are not used.

i. Click OK to close the Wireless network properties window, and then click OK again.

j. Click OK again to close the Wireless Network Properties Connection window.

Network setup

Create a network profile for other operating systems

If you have an operating system other than Windows XP, HP recommends that you use the configuration program that came with your wireless LAN card. To find the configuration program for your wireless LAN card, access your computer's list of programs.

Using the LAN card configuration program, create a network profile that has the following values:

•Network name (SSID): Mynetwork (example only)

NOTE: You should create a network name that is unique and easy for you to remember. Just remember that the network name is case-sensitive. Therefore, you must remember which letters are uppercase and lowercase.

•Communication mode: Ad Hoc

•Encryption: enabled

Connect to a wireless ad hoc network

You can use the Wireless Setup Wizard to connect the HP All-in-One to a wireless ad hoc network.

To connect to a wireless ad hoc network

1.On the control panel of the HP All-in-One, press Setup.

2.Press until Network is highlighted, and then press OK.

14 Network setup

Page 15 Page 17
Image 16
Page 15 Page 17
Contents
HP Photosmart C7200 All-in-One series Hewlett-Packard Company notices Contents Troubleshooting and support Technical informationHP All-in-One overview HP All-in-One at a glanceControl panel features One overviewLabel Name and Description Find more information Setup GuideOnscreen Help Network setup Wired network setupConnect the HP All-in-One to the network What you need for a wired networkTo connect the HP All-in-One to the network Integrated wireless Wlan 802.11 network setup What you need for an integrated wireless Wlan 802.11 network Connect to an integrated wireless Wlan 802.11 networkTo connect the HP All-in-One with the Wireless Setup Wizard If you do not see your network name in the listWireless ad hoc network setup To connect the HP All-in-One with SecureEasySetupWhat you need for an ad hoc network Create a network profile for a Windows XP computerConnect to a wireless ad hoc network Communication mode Ad Hoc Encryption enabledTo connect to a wireless ad hoc network Create a network profile for other operating systemsPress to highlight Wireless Setup Wizard, and then press OK To install the Windows HP All-in-One software Install the software for a network connectionConnect to additional computers on a network Change basic network settings from the control panel Manage your network settingsTo change a USB connection to a wired Ethernet connection Use the Wireless Setup Wizard View and print network settingsRestore network defaults Turn the wireless radio on and offPrint the wireless network test Change IP settingsSet link speed Automatic Full HalfIP Address Subnet Mask Default Gateway Fax setup Set up the HP All-in-One for faxingCase a Separate fax line no voice calls received Case B Set up the HP All-in-One with DSL To set up the HP All-in-One with a separate fax lineTo set up the HP All-in-One with DSL Case D Fax with a distinctive ring service on the same line To set up the HP All-in-One with a distinctive ring service Case E Shared voice/fax lineTo set up the HP All-in-One with a shared voice/fax line Case F Shared voice/fax line with voice mailSet the answer mode Change settings on the HP All-in-One to receive faxesTo set up the HP All-in-One with voice mail Set the number of rings before answering To set the answer modeChange the answer ring pattern for distinctive ringing Test your fax setup To test your fax setup from the control panelTo set a default fax header from the control panel Set the fax headerSet the fax header Load an original in the automatic document feeder Load originals and load paperTo load an original in the document feeder tray Load an original on the glass Load full-size paperTo load an original on the scanner glass To load full-size paperChapter Load 10 x 15 cm 4 x 6 inch photo paper To load 10 x 15 cm 4 x 6 inch photo paper in the photo trayAvoid paper jams View and select photosTo view, select, and print photos Scan an original to a computer Scan an imageScan an original to a memory card or storage device Make a copy Send a basic faxTo save a scan to a memory card or storage device To make a copy from the control panelCheck the estimated ink levels To send a basic fax from the control panelPress Fax Menu To check the ink levels from the control panelReplace the ink cartridges To replace the ink cartridgesUse HP All -in One features Clean the glass Clean the HP All-in-OneTo clean the glass Clean the lid backing To clean the lid backing Hardware setup troubleshooting Uninstall and reinstall the softwareHP All-in-One will not turn on Solution Wrong measurements are showing in menus on the display Display shows the wrong languageTo set your language and country/region Wired network setup troubleshooting Network troubleshootingHP All-in-One does not print Printer not Found screen appears during installation Computer is unable to discover the HP All-in-OneWireless setup troubleshooting To make sure your network connection is activeCannot connect to network during setup Connect to an integrated wireless Wlan 802.11 network onInvalid WEP key during wireless setup Invalid passphrase during wireless setupNetwork software installation troubleshooting Received a System Requirements Error No TCP/IPFax setup troubleshooting Fax test failedFax Hardware Test failed Solution What to doFax Connected to Active Telephone Wall Jack test failed Phone Cord Connected to Correct Port on Fax test failed Using Correct Type of Phone Cord with Fax test failed Dial Tone Detection test failed HP All-in-One is having problems sending and receiving faxes Fax Line Condition test failedTroubleshooting and support Try setting the Fax Speed to Medium 14400 or Slow If you hear noiseHP All-in-One is having problems sending a manual fax HP All-in-One cannot send faxes, but can receive faxesHP All-in-One cannot receive faxes, but can send faxes Troubleshooting and support Fax tones are recorded on my answering machine Clear paper jams To clear a paper jam from the Two-sided printing accessoryTo clear a paper jam in the automatic document feeder Information on ink cartridges and the print head If you have a problem, follow these steps Support processSystem requirements Product specificationsEnergy Star notice Ink cartridge yield Regulatory notices Regulatory model identification numberWarranty Technical information
Related manuals
Manual 309 pages 10.38 Kb Manual 16 pages 46.21 Kb
Top Page Image Contents