HP C7100 manual Connect to a wireless ad hoc network, Communication mode Ad Hoc Encryption enabled

Page 23

Network setup

Chapter 2

configuration program for your wireless LAN card, access your computer's list of programs.

If you have an operating system other than Mac OS X, HP recommends that you use the configuration program that came with your wireless LAN card. To find the configuration program for your wireless LAN card, access your computer's list of programs.

Using the LAN card configuration program, create a network profile that has the following values:

Network name (SSID): Mynetwork (example only)

Communication mode: Ad Hoc

Encryption: enabled

Note You should create a network name that is not the same as the example shown here, such as your initials. Just remember that the network name is case-sensitive. Therefore, you must remember which letters are uppercase and lowercase.

Connect to a wireless ad hoc network

You can use the Wireless Setup Wizard to connect the HP All-in-One to a wireless ad hoc network.

To connect to a wireless ad hoc network

1.On the control panel of the HP All-in-One, press Setup.

2.Press until Network is highlighted, and then press OK.

3.Press to highlight Wireless Setup Wizard, and then press OK.

This runs the Wireless Setup Wizard. The setup wizard searches for available networks, and then displays a list of detected network names (SSIDs). The infrastructure networks appear first in the list, followed by available ad hoc networks. The networks with the strongest signal appear first, the weakest appear last.

4.On the display, look for the network name you created on your computer (for example, Mynetwork).

5.Use the arrow buttons to highlight the network name, and then press OK. If you found your network name and selected it, go on to step 6.

If you do not see your network name in the list

a.Select Enter a New Network Name (SSID). The visual keyboard appears.

b.Enter the SSID. Use the arrow buttons on the HP All-in-One control panel to highlight a letter or number on the visual keyboard, and then press OK to select it.

Note You must enter the exact uppercase (capital) and lowercase (small) letters. Otherwise, the wireless connection will fail.

c.When you are finished entering the new SSID, use the arrow buttons to highlight Done on the visual keyboard, and then press OK.

d.Press until Ad Hoc is highlighted, and then press OK.

20

HP Photosmart C7100 All-in-One series

Image 23
Contents HP Photosmart C7100 All-in-One series Basics Guide Hewlett-Packard Company notices Contents Index Scan Print photosPrint from your computer CopyLabel Description HP All-in-One at a glanceControl panel features Label Name and Description Use the HP Photosmart software HP Photosmart Mac Help appears Access the onscreen HelpFind more information See this section Wired network setupIf you want to Connect the HP All-in-One to the network What you need for a wired networkTo connect the HP All-in-One to the network Install the software for a network connectionTo install the Mac HP All-in-One software To install the Windows HP All-in-One softwareIntegrated wireless Wlan 802.11 network setup Connect to an integrated wireless Wlan 802.11 network What you need for an integrated wireless Wlan 802.11 networkIf you do not see your network name in the list To connect the HP All-in-One with the Wireless Setup WizardWhat you need for an ad hoc network Wireless ad hoc network setupOn the Windows Control Panel, click Security Center To disable LAN connections with Windows XPPrepare a Windows XP computer To prepare your computerPrepare a Mac Click Show Options Create a network profile for other operating systemsTo create a new network profile Select Create Network…To connect to a wireless ad hoc network Connect to a wireless ad hoc networkCommunication mode Ad Hoc Encryption enabled Connect to additional computers on a network To run the Wireless Setup Wizard Manage your network settingsChange basic network settings from the control panel To turn the wireless radio on and off Restore network defaultsTo restore network defaults Turn the wireless radio on and offAutomatic Full Half Use the Embedded Web Server IP Address Subnet Mask Default GatewayAccess the Embedded Web Server To access the Embedded Web ServerGeneral network settings Network configuration page definitionsUse the Embedded Web Server setup wizard To access the Embedded Web Server setup wizardParameter Wired 802.3 network settingsDefault Gateway Wireless 802.11 network settings When you use the web or send an e-mail message, you use a Ssid Parameter Bluetooth settings Countries/regions with a parallel-type phone system Set up the HP All-in-One for faxingUSA Choose the correct fax setup for your home or officeSelect your fax setup case Recommended fax setup for serial-type phone systems Other equipment/ services sharing your fax lineRecommended fax setup for parallel-type phone systems Machine ServiceNot applicable Up modem, and answeringBack view of the HP All-in-One Case B Set up the HP All-in-One with DSLTo set up the HP All-in-One with a separate fax line Case a Separate fax line no voice calls receivedTo set up the HP All-in-One with DSL Fax setup To set up the HP All-in-One with a distinctive ring service Case D Fax with a distinctive ring service on the same lineCase E Shared voice/fax line To set up the HP All-in-One with a shared voice/fax lineCase F Shared voice/fax line with voice mail To set up the HP All-in-One with a computer dial-up modem To set up the HP All-in-One with voice mailCase H Shared voice/fax line with computer dial-up modem Fax Example of a parallel splitterAnswering machine Case I Shared voice/fax line with answering machineFax setup Example of a parallel splitter Fax setup Example of a parallel splitter Set the answer mode Change settings on the HP All-in-One to receive faxesChange the answer ring pattern for distinctive ringing To set the answer modeSet the number of rings before answering Set the fax header Test your fax setupTo test your fax setup from the control panel To set a default fax header from the control panel To load an original on the glass Load originals and load paperLoad originals Load 10 x 15 cm 4 x 6 inch photo paperTo load 10 x 15 cm 4 x 6 inch photo paper in the photo tray Load an original in the Slide and Negative Film holderTo load 35 mm slides To load 35 mm negativesLower the lid of the HP All-in-One before starting the scan To make a copy from the control panel Avoid paper jamsMake a copy Scan an imagePress OK to select Select Computer Scan an original to a computerMake reprints of your photos Press Scan MenuPrint Preview Defaults optionScan an original to a memory card or storage device Print OptionsTo change the original type Scan slides or negative filmTo save a scan to a memory card or storage device To scan a slide or negativeTo print one or more 10 x 15 cm 4 x 6 inch photos Print 10 x 15 cm 4 x 6 inch photosPress OK to select Select to Print To print more than one copy of the selected photoTo edit the selected photo before printing To select additional photos for printingTo print from a software application Mac Print from a software applicationPrint Preview Print Now To print from a software application WindowsPress Start Fax Black again Send a basic faxPress Fax Menu Press Start Fax BlackTo replace the ink cartridges Replace the ink cartridgesIf you do not have another page to fax Use the HP All-in-One features Align the printer To clean the glass Clean the HP All-in-OneClean the glass Clean the lid backingTo clean the lid backing Clean the exteriorTo uninstall from a Windows computer and then reinstall Uninstall and reinstall the softwareTroubleshooting common setup issues HP All-in-One will not turn on Hardware setup troubleshootingTo uninstall from a Mac and then reinstall To set your language and country/region Display shows the wrong languageHP All-in-One does not print Fax setup troubleshootingFax test failed What to do Fax Hardware Test failedFax Connected to Active Telephone Wall Jack test failed Phone Cord Connected to Correct Port on Fax test failed Using Correct Type of Phone Cord with Fax test failedDial Tone Detection test failed Fax Line Condition test failed HP All-in-One is having problems sending and receiving faxesTroubleshooting and support Troubleshooting and support Try setting the Fax Speed to Medium 14400 or Slow HP All-in-One cannot send faxes, but can receive faxes If you hear noise, do the followingHP All-in-One is having problems sending a manual fax HP All-in-One cannot receive faxes, but can send faxes Troubleshooting and support Troubleshooting and support Fax tones are recorded on my answering machine Telephone wall jack Wired network setup troubleshooting Network setup troubleshootingTo make sure your network connection is active Received a System Requirements Error No TCP/IPPrinter not Found screen appears during installation To establish an active network connectionYou do not see the Ssid Wireless setup troubleshootingTo print the network configuration Error message Cannot connect to network Weak signalCause An invalid WEP key was entered Error message Invalid WEP KeyError message More than 1 SecureEZ Setup access point found Network software installation troubleshootingError message Invalid passphrase To clear a paper jam from the rear door Clear paper jamsCannot print Calibration errorInformation on ink cartridges Ink cartridge messagesInk expiration near Ink cartridge problemInk cartridges are empty Ink cartridges are expiredOriginal HP ink depleted Print head assembly is stalledNon-HP ink Replace ink cartridges soon To clear the print head assemblyPrint head failure Printer alignment failedWrong ink cartridges installed Phone support period Placing a call Additional warranty optionsSupport process HP support by phonePaper tray capacities Paper specificationsPrint specifications System requirementsPhysical specifications Copy specificationsScan specifications Fax specificationsRegulatory model identification number Environmental specificationsInk cartridge warranty information Regulatory noticesWarranty Index Negatives Basics Guide 111 112